Publicidad
Idiomas disponibles
Idiomas disponibles
FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
This insTrucTion Manual conTains
iMporTanT safeTy inforMaTion.
read This
insTrucTion Manual
carefully and
undersTand all
inforMaTion Before
operaTing This Tool.
• Always operate, inspect and maintain
this tool in accordance with American
National Standards Institute Safety
Code of Portable Air Tools (ANSI
B186.1) and any other applicable safety
codes and regulations.
• For safety, top
performance and
maximum durability of
parts, operate this tool
at 90 psig; 6.2 bar max
air pressure with 3/8"
diameter air supply
hose.
• Always wear impact-
resistant eye and face
protection when
operating or performing
maintenance on this
tool.
• High sound levels can
cause permanent
hearing loss. Always use
hearing protection as
recommended by your
employer and OSHA
regulations while using
this tool.
• Keep the tool in efficient operating
condition.
• Operators and maintenance personnel
must be physically able to handle the
bulk, weight and power of this tool.
• Air powered tools can
vibrate during use.
Extended exposure to
vibration, repetitive
motions, or
uncomfortable positions
during use may be
harmful to your hands and arms.
Discontinue use of tool if discomfort,
tingling, or pain occurs. Seek medical
advice before resuming use.
please revieW all Warning insTrucTions prior To operaTion. save This Man u al for fuTure ref er ence.
2
2
• Compressed air can
cause severe injury.
Never direct air at
yourself or others.
Always turn off the
air supply, drain hose
of air pressure and
detach tool from air
supply before installing,
removing or adjusting
any part or accessory on
this tool, or before
performing any
maintenance on this
tool. Failure to do so
could result in injury.
Whip hoses can cause
serious injury. Always
check for and replace
any damaged, frayed
or loose hoses and fittings. Do not
operate a damaged or worn tool. Do
not use quick-detach couplings at tool.
See instructions for correct set-up.
• Place the tool on the work before
starting the tool. Do not point or
indulge in any horseplay with this tool.
• Slipping, tripping
and/or falling while
operating air tools can
be a major cause of
serious injury or death.
Be aware of excess hose
left on the walking or
work surface.
• Keep body working stance balanced
and firm. Do not overreach when
operating the tool.
• Anticipate and be alert for sudden
changes in motion during use of any
power tool.
• Do not carry tool by the
hose. Protect the hose
from sharp objects and
heat.
• Tool shaft may continue
to rotate briefly after
throttle is released.
Avoid direct contact
with accessories during
and after use. Gloves
will reduce the risk of
cuts or burns.
• Keep away from
rotating end of tool.
Do not wear jewelry or
loose clothing. Secure
long hair. Scalping can
occur if hair is not kept
away from tool and
accessories. Choking can occur if
neckwear is not kept away from tool
and accessories.
• Do not lubricate tools with flammable
or volatile liquids such as kerosene,
diesel or jet fuel.
• Correct wire belt and eraser mounting
is necessary to prevent injury. Do not
use wire belts or eraser wheels that
have been broken or damaged in
any way.
• Wheel hubs should be a free fit on
the spindle to prevent stress at the
mounting location. Use only hubs
that come with the metal blaster for
mounting wire belts and eraser wheels.
• Flat washers or other adapters may
over stress the wheel hub. Always
use factory recommended mounting
hardware.
• Tighten the wheel hub on the spindle
to prevent spin off with the tool
turned off and air supply disconnected.
• Use only accessories rated at or higher
than the tools RPM's.
• Do not force tool beyond its rated
capacity.
• Do not remove any labels. Replace
damaged labels.
• Use accessories recommended by
NAPA Professional Air Tools.
6-1039
Publicidad
