Turning Off - BERTO'S 9GL22 Serie Manual De Instrucciones

(PILOT) position.
In this position, keep the knob pressed down while
pushing the piezoelectric button several time until the
pilot flame ignites. For the (/R) models, turn the knob to
activate the piezoelectric button (see fig. 13).
Release the knob after 5 seconds and turn it to the desired
position. Repeat the same operation if the pilot flame goes
out.
Pilot burner ignition (GL18...,SGL18...,9GL18...,S9GL18...,LX9GL18..
.,9GL22...EL,S9GL22...EL,LX9GL22...EL) (fig. 11)
Rotate the knob (1) clockwise up to the position (
this position, press the knob until the pilot flame lights
up. Release the knob after 60 seconds and rotate it to the
position . Repeat the operation if the pilot flame goes
out.
Main burner Ignition and temperature regulation
To turn on the main burner, rotate the knob further
anticlockwise up to the desired temperature. The
thermostat valve is marked in positions from 1 to 8 for the
600 Series and from 1 to 7 for the 700/900 Series.
The values indicating the temperature in each position are
the following:
8 position valve
Position 0 1 2
Temperature °C Off 110 121 133 145 156 168 179 190
7 position valve
Position 0 1 2
Temperature °C Off 115 130 143 157 171 180 190
Main burner Ignition and temperature regulation
(GL18...MI, SGL18...MI, 9GL18...MI,
LX9GL18...MI)
To switch the main burners, rotate the thermostat knob on
the panel up to the desired temperature value.

TURNING OFF

Turning off during normal operation (fig. 9-10)
TURNING OFF (600SERIES). To turn off the main burners,
rotate the knob (1) to the position (
only, the pilot flame is switched on. To turn off the
appliance completely, press the off button (
Before switching on again, wait for about 1 minute so that
the valve releases.
TURNING OFF (700/900 SERIES). To turn off the main
burners, rotate the knob (1) to the position (
position, only the pilot flame is switched on. To turn off the
appliance completely, rotate the knob up to the position
( ).
TURNING OFF (electronic controls). To turn off the main
burners, rotate the knob (1) to the position (
position, only the pilot flame is lit. To turn off the appliance
completely, rotate the knob up to the position (
the START/STOP button on the electronic controller.
Turning
S9GL18...MI, LX9GL18...MI)
To turn off the main burners, rotate the thermostat knob on
the panel up to zero; rotate the knob (1) up to the position
(
To completely turn off the appliance, rotate the knob (1)
up to the position (
Turning off in the event of a failure
In the event of a failure, cut off the gas supply to the
appliance.
). In
What to do in case of malfunctioning or if the appliance
is not used for a long period of time
If the appliance is not to be used for a long period of time,
or in the event of a failure or malfunctioning, turn off the
external gas supply tap connecting to the main line. After
performing all cleaning operations, the stainless steel
surfaces should be well dried and protected with standard
anti-corrosion products. In the event of a failure, call
Technical Assistance.
Regulating the cooking temperature (see fig. 14)
When the fryer is off and the supply cord is plugged in, the
3 4 5 6 7 8
"A" displays shows the temperature of the oil in the tank.
Softly press the (B) arrows to increase or decrease the
cooking temperature.
The display will show the value of the selected temperature
and an acoustic signal will confirm the setting has been
3 4 5 6 7
recorded.
After this operation, the display will again show the
present temperature value in the tank.
The cooking temperature regulation can be carried out
when the fryer is working or when it is off.
S9GL18...MI,
If the set value is lower than the temperature value of the
oil in the tank, it will be necessary to wait for the oil to cool
down.
Switching the fryer ON and OFF (see fig. 14)
The fryer is equipped with an electrical ignition of the
pilot flame; therefore, make sure that you have properly
connected the fryer to the electrical network.
Press and rotate the valve handle to the ignition position
) ; in this position
flame and waiting a few seconds for the thermocouple to
) (4).
heat up before releasing it.
Press and rotate the handle in the operating position ,
now keeping the second start key "C" for a few seconds to
switch the fryer on. The green Led "D" will start flashing
) ; in this
and the burners will switch on.
When the temperature is set, the fryer will emit an acoustic
signal and keep the temperature of the oil constant by
automatically switching on and off when necessary.
Every time that the set temperature is reached, the fryer
) ; in this
will emit an acoustic signal.
To switch the fryer off, press the "C" button down for few
), press
seconds; the burners will switch off and the green LED "D"
will stop flashing.
Only the pilot flame will be on and the "A" display will show
off (GL18...MI, SGL18...MI,
); in this position, only the pilot flame is switched on.
).
OPERATIONS WITH ELECTRONIC CONTROLS
, keeping it pressed down while igniting the pilot
| 67
9GL18...MI,
EN