Battery Pack - Metabo MKS 18 LTX 58 Instrucciones De Manejo

en ENGLISH
Avoid overheating of the saw tooth tips. Use a
saw blade that is suitable for the material being
sawn.
If the machine is defective, remove the battery pack
from the machine.
Protect battery packs from water and
moisture!
Do not use faulty or deformed battery packs!
Do not expose battery packs to fire!
Do not open battery packs!
Do not touch or short circuit battery pack contacts!
Remove the battery pack from the machine
when not in use.
Remove the battery pack from the tool before
any adjustments, conversions, servicing or
cleaning are performed.
Make sure that the tool is switched off before
fitting the battery pack.
A slightly acidic, flammable fluid may leak
from defective Li-ion battery packs!
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical attention imme-
diately!
Transport of li-ion battery packs:
The shipping of li-ion battery pack is subject to laws
related to the carriage of hazardous goods (UN
3480 and UN 3481). Inform yourself of the currently
valid specifications when shipping li-ion battery
packs. If necessary, consult your freight forwarder.
Certified packaging is available from Metabo.
Only send the battery pack if the housing is intact
and no fluid is leaking. Remove the battery pack
from the machine for sending. Secure the contacts
against short circuiting (e. g. insulate with tape).
Additional Warnings:
WARNING
drilling, and other construction activities
contains chemicals known to cause cancer,
birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and
other masonry products, and
• Arsenic and chromium from chemicallytreated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
8
California Prop 65 08_2018
Some dust created by power
sanding, sawing, grinding,
SYMBOLS ON THE TOOL:
V .............. volts
...........direct current
rpm..........revolutions per minute
.../min ......revolutions per minute
n ............no load speed
0
Ø .............saw blade diameter
4. Overview
See page 2.
1 Shavings collection box
2 Handle
3 Trigger
4 Locking button
5 Side handle
6 Guide rail adapter*
7 Locking screw (parallel stop, guide rail adapter)
8 View window (exchangeable)
9 Cutting indicator
10 Parallel stop

11 Battery pack *

12 Battery pack release button
13 Guide plate
14 Scale (depth of cut)
15 Storage for hexagon wrench
16 Hexagon wrench
17 Locking lever (depth of cut)
18 Capacity and signal indicator *
19 Capacity indicator button *
20 Spindle locking button
21 Saw blade fixing screw
22 Outer saw blade flange
23 Saw blade
24 Lever (swivelling back the movable guard)
25 Inner saw blade flange
26 Movable safety guard
*equipment-specific
5. Initial Operation and Setting
Remove the battery pack from the tool before
any adjustments, conversions, servicing or
cleaning are performed. Make sure that the tool is
switched off before fitting the battery pack.
5.1 Battery pack
Charge the battery pack (11) before use.
Recharge the battery pack if performance dimin-
ishes.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
Li-Ion battery packs "Li-Power, LiHD" have a
capacity and signal indicator (18):
- Press the button (19), the LEDs indicate the
charge level.
- The battery pack is almost flat and must be
recharged if one LED is flashing.