Bestway POWER STEEL 56629 Manual De Instrucciones página 9

Ocultar thumbs Ver también para POWER STEEL 56629:

Manual de instrucciones (56 páginas)

página de 40

/ 40
Marcadores

Idiomas disponibles

POOL MAINTENANCE

WARNING: If you do not adhere to the maintenance guidelines

covered herein, your health might be at risk, especially that of children.

Pool water treatment is essential for the safety of the users. Using

chemicals inappropriately will cause property damage and personal

injury.

NOTE: The pump is used to circulate the water and to filter small

particles. In order to keep your pool water clean and hygienic, you

must also add chemicals.

1. It is recommended not to fill the pool with catchment water, drilling

water, or drainage well water: these waters generally contain

polluted organic substances including nitrates and phosphates.

Filling pools with water from the public network is advised.

2. Always keep your pool clean and apply the correct pool chemicals.

Unsanitary water is a serious health hazard. It is recommended to

use disinfectant, flocculant, acid or alkali chemicals to treat your

pool.

Parameters

Water clarity

Colour of the water

Turbidity in FNU/NTU

Nitrate concentration above that of fill water in mg/l

Total organic carbon (TOC) in mg/l

Redox potential against Ag/AgCI 3,5 m KCl in mV

pH value

Free active chlorine (without cyanuric acid) in mg/l

Free chlorine used in combination with cyanuric acid in mg/l

Cyanuric acid in mg/l

Combined chlorine in mg/l

ATTENTION: Do not use pump when pool is in use.

During the season of use of the swimming pool, the filtration system must be necessarily put into service every day, enough for a long time to

assure at least a complete renewal of the volume of water.

Repair

Check pool for any leaks from valves or seams, check the ground cloth for any evident water loss. Do not add chemicals until this has been done.

NOTE: In the event of a leak, patch your pool using the underwater adhesive repair patch provided. Refer to the FAQs for further information.

Dismantling

1. Unscrew the drain valve cap on the outside of the pool counter clockwise and remove.

2. Connect the adaptor to the hose and put the other end of the hose in the area where you are going to drain your pool. (Check local regulations

for drainage by-laws).

3. Screw the control ring of the hose adaptor clockwise onto the drain valve. The drain valve will be open and water will start to drain automatically.

ATTENTION: Water flow can be controlled with the control ring.

4. When draining is finished, unscrew the control ring to close the valve.

5. Disconnect the hose.

6. Screw the cap back onto the drain valve.

7. Air dry pool.

ATTENTION: Do not leave the drained pool outside.

Storage and Winterization

1. Please remove all the accessories and spare parts of the pool and store them clean and dry.

2. Once pool is completely dry, sprinkle with talcum powder to prevent pool from sticking together, fold pool carefully. If pool is not completely dry,

mold may result and will damage the pool liner.

3. Store liner and accessories in a dry place with a moderate temperature between 5ºC / 41ºF and 38ºC / 100ºF.

4. During the rainy season, pool and accessories should be stored as per above instructions also.

5. Improper draining of the pool might cause serious personal injury and/or damage to personal property.

6. We strongly recommend the pool is disassembled during the off season (winter months). Store in a dry location out of children's reach.

3. Clean the PVC liner regularly with non-abrasive brushes or a pool

vacuum cleaner.

4. Throughout the season, the water filtration system must run long

enough each day to clean the entire volume of water in the pool.

5. Check the filter cartridge (or sand in a sand filter) regularly and

replace dirty cartridges (or sand).

6. Regularly check the screws, bolts and all the metal parts for rust.