Specific Safety Rules - Makita DA6301 Manual De Instrucciones

ENGLISH
1 Tighten
2 Chuck
3 Chuck key
4 Spade grip
5 Hex. bolt
6 Brace pipe here.
7 Reaction
SPECIFICATIONS
Model
Drilling capacities
Wood
Auger-bit ..................................................................................................................................... High: 29 mm (1-1/8")
Ship-auger-bit ............................................................................................................................. High: 38 mm (1-1/2")
Self-feed bit ................................................................................................................................ High: 35 mm (1-3/8")
Steel ............................................................................................................................................... High: 13 mm (1/2")
–1
No load speed (min ) ................................................................................................................................... High: 1,200
Overall length .............................................................................................................................................330 mm (13")
Overall length (Extended spade grip) .................................................................................................410 mm (16-3/16")
Net weight ................................................................................................................................................4.3 kg (9.5 lbs)
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to drill safety rules. If you use this power tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
1. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
2. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the opeator.
3. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4. Hold the tool firmly.
5. Keep hands away from rotating parts.
6. Do not leave the tool running. Operate the tool
only when hand-held.
4
Explanation of general view
8 Forward
9 Drilling in forward bit turns
clockwise
10 Reverse
11 Reversing bit turns counter-
clockwise
12 Counterclockwise
7.
8.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
GEB001-2
OPERATING INSTRUCTIONS
Installing or removing drill bit (Fig. 1)
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each
of the three holes and tighten clockwise. It is important to
tighten the chuck with all three holes evenly. To remove
the bit, turn the chuck key counterclockwise in just one
hole, then loosen the chuck by hand.
Spade grip (Fig. 2 & 3)
The spade grip can be installed in either of the positions
as shown in the figure. When changing the location of the
spade grip from one position to the other, loosen the hex
bolts with a wrench and turn the spade grip to another
position. Then tighten the hex bolts securely.
13 Switch
14 Clockwise
15 Pin
16 Slide button
17 Limit mark
18 Screwdriver
19 Brush holder cap
Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
DA6301
Low: 38 mm (1-1/2")
Low: 38 mm (1-1/2")
Low: 118 mm (4-5/8")
Low: 13 mm (1/2")
Low: 300