Easy Maintenance Function - Mitsubishi Electric Mr. Slim PLA-RP-BA Serie Manual De Instalación

. Installing the grille
10. Easy maintenance function (For PUHZ-(H)RP application only)
Display example (Comp discharge temperature 64˚C)
D
A
PAR-21MAA
(1) Press the button for 3 seconds to
TEST
activate the maintenance mode.
(2) Press the TEMP. buttons to set the refrigerant address.
(3) Select the data you want to display.
Compressor Cumulative
operation time
information
Display A COMP ON
MENU
x10 HOURS
Heat exchanger
Outdoor unit
temperature
information
OUTDOOR UNIT
Display A
H•EXC. TEMP
ON/OFF
Indoor room
Indoor unit
temperature
information
Display INDOOR UNIT
A
INLET TEMP
* The filter operation time displayed is the number of hours the filter has been
used since the filter reset was performed.
(4) Press the button.
FILTER
(5) The data is displayed in .
C
Display
* Repeat steps (2) to (5) to check another data.
(6) Press the button for 3 seconds or press the
TEST
deactivate the maintenance mode.
Button
Vane motor
Up/down vanes
Connector
Fig. 9-11
C
B
Maintenance mode operation procedures
MAINTENANCE
Display
A
Display B
ON/OFF Operation
current
number
COMP ON
COMP ON
x100 TIMES
CURRENT (A)
Outdoor ambient
Comp discharge
temperature temperature
OUTDOOR UNIT OUTDOOR UNIT
OUTLET TEMP
OUTDOOR TEMP
Filter operation
Heat exchanger
time
temperature
INDOOR UNIT
INDOOR UNIT
H•EXC. TEMP FILTER USE H
(Airflow temperature display example)
Blinking
C
Approx.
Waiting for 64
10 sec.
response
button to
ON/OFF
9.7. Locking the up/down airflow direction (Fig. 9-11)
The vanes of the unit can be set and locked in up or down orientations depending
upon the environment of use.
• Set according to the preference of the customer.
The operation of the fixed up/down vanes and all automatic controls cannot
be performed using the remote controller. In addition, the actual position of the
vanes may differ from the position indicated on the remote controller.
Turn off the main power switch.
1
Injuries or an electrical shock may occur while the fan of the unit is rotating.
Disconnect the connector for the vane motor of the vent that you want to lock.
2
(While pressing the button, remove the connector in the direction indicated by the
arrow as shown in the diagram.) After removing the connector, insulate it with tape.
It also can be set by remote controller. Refer to 6.3.3.
9.8. Check
• Make sure that there is no gap between the unit and the grille, or between the grille
and the surface of the ceiling. If there is any gap between the unit and the grille, or
between the grille and the surface of the ceiling, it may cause dew to collect.
• Make sure that the wires have been securely connected.
• For PLP-6BAE, PLP-6BAMDE, PLP-6BALME, check the rotating movement of
the i-see sensor. If the i-see sensor does not rotate, review the procedure in "9.6.
Installation of i-see sensor corner panel".
By using the maintenance mode, you can display many types of maintenance data
on the remote controller such as the heat exchanger temperature and compressor
current consumption for the indoor and outdoor units.
This function can be used whether the air conditioner is operating or not.
During air conditioner operation, data can be checked during either normal opera-
tion or maintenance mode stable operation.
* This function cannot be used during the test run.
* The availability of this function depends on the connecting outdoor unit. Refer to
the brochures.
Stable operation
Using the maintenance mode, the operation frequency can be fixed and the op-
eration can be stabilized. If the air conditioner is stopped, use the following pro-
cedure to start this operation.
Press the button to select the operation mode.
MODE
Stable cooling
operation
Display COOL
A
STABLE MODE
Press the button.
FILTER
Waiting for
stable operation
Display D
* You can check the data using steps (3) to (5) of the maintenance mode opera-
tion procedures while waiting for the stable operation.
Stable operation
Stable heating
cancellation
operation
HEAT
STABLE MODE
STABLE MODE CANCEL
Stable
operation
10-20 min.
1