Remote Controller - Mitsubishi Electric Mr. Slim PLA-RP-BA Serie Manual De Instalación

6. Electrical work
30 30
46
Fig. 6 - 2
B-1.
Fig. 6 - 3
Fig. 6-4
Fig. 6 - 5
MODEL SELECT
ON/OFF TEMP
FAN AUTO STOP
MODE VANE AUTO START
CHECK LOUVER h
TEST RUN min
SET RESET CLOCK
Fig. 6-7
B-2.
A B TB 6
MODEL SELECT
ON/OFF TEMP
FAN AUTO STOP
MODE VANE AUTO START
CHECK LOUVER h
TEST RUN min
SET RESET CLOCK
Fig. 6-6

6.. Remote controller

6..1. For wired remote controller
1) Installing procedures
(1) Select an installing position for the remote controller. (Fig. 6-2)
The temperature sensors are located on both remote controller and indoor unit.
► Procure the following parts locally:
2 piece switch box
Thin copper conduit tube
Lock nuts and bushings
[Fig.6-]
A Remote controller profile
B Required clearances surrounding the remote controller
C Installation pitch
(2) Seal the service entrance for the remote controller cord with putty to prevent
possible invasion of dew drops, water, cockroaches or worms. (Fig. 6-3)
A For installation in the switch box
B For direct installation on the wall, select one of the following:
• Prepare a hole through the wall to pass the remote controller cord (in order to run
the remote controller cord from the back), then seal the hole with putty.
• Run the remote controller cord through the cut-out upper case, then seal the cut-
out notch with putty.
B-1. To lead the remote controller cord from the back of the controller
B-. To run the remote controller cord through the upper portion
[Fig.6-3]
Wall Switch box
C G
Conduit Remote controller cord
D H
Lock nut Seal with putty
E I
Bushing Wood screw
F J
2) Connecting procedures (Fig. 6-4)
1 Connect the remote controller cord to the terminal block.
A To TB5 on the indoor unit
B TB6 (No polarity)
3)  remote controllers setting
If 2 remote controllers are connected, set one to "Main" and the other to "Sub". For
setting procedures, refer to "Function selection of remote controller" in the opera-
tion manual for the indoor unit.
6... For wireless remote controller
1) Installation area
• Area in which the remote controller is not exposed to direct sunshine.
• Area in which there is no nearby heating source.
• Area in which the remote controller is not exposed to cold (or hot) winds.
• Area in which the remote controller can be operated easily.
• Area in which the remote controller is beyond the reach of children.
) Installation method (Fig. 6-5)
1 Attach the remote controller holder to the desired location using 2 tapping screws.
2 Place the lower end of the controller into the holder.
A Remote controller B Wall C Display panel D Receiver
• The signal can travel up to approximately 7 meters (in a straight line) within 45
degrees to both right and left of the center line of the receiver.
3) Setting (Fig. 6-6)
1 Insert batteries.
2 Press the SET button with something sharp at the end.
blinks and Model No. is lighted.
MODEL SELECT
3 Press the temp buttons to set the Model No.
If you mistook the operation, press the ON/OFF
from procedure 2.
4 Press the SET button with something sharp at the end.
and Model No. are lighted for 3 seconds, then turned off.
MODEL SELECT
Indoor Outdoor
PUH, PUHZ, SUZ
PLA
PU
4)Automatic fan speed setting (For wireless remote controller)
It is necessary to set for wireless remote controller only when automatic fan
speed is not set at initial setting.
It is not necessary to set for wired remote controller with automatic fan speed at
initial setting.
1. Press the SET button with something sharp at the end.
Operate when display of remote controller is off.
blinks and Model No. is lighted A.
MODEL SELECT
2. Press the AUTO STOP button.
blinks and setting No. is lighted B.
(Setting No.01: without automatic fan speed )
3. Press the temp. buttons to set the setting No.02.
(Setting No.02:with automatic fan speed )
If you mistook the operation, press the ON/OFF
from procedure 2.
4. Press the SET button with something sharp at the end.
and Model No. are lighted for 3 seconds, then turned off.
MODEL SELECT
button and operate again
Model No.
A
001
033
button and operate again