Napa 6-1078 Manual De Instrucciones página 2

FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
This insTrucTion Manual conTains
iMporTanT safeTy inforMaTion.
read This insTrucTion
Manual carefully
and undersTand all
inforMaTion Before
operaTing This Tool.
• Always operate, inspect and maintain
this tool in accordance with American
National Standards Institute Safety
Code of Portable Air Tools (ANSI
B186.1) and any other applicable safety
codes and regulations.
• For safety, top
performance and
maximum durability of
parts, operate this tool
at 90 psig; 6.2 bar max
air pressure with 1/2"
diameter air supply
hose.
• Always wear impact-
resistant eye and face
protection when
operating or performing
maintenance on this
tool (users and
bystanders).
• High sound levels can
cause permanent
hearing loss. Always use
hearing protection as
recommended by your
employer and OSHA
regulations while using
this tool (users and
bystanders).
• Keep the tool in efficient operating
condition.
• Operators and maintenance personnel
must be physically able to handle the
bulk, weight and power of this tool.
• Air powered tools can
vibrate during use.
Extended exposure to
vibration, repetitive
motions, or
uncomfortable positions
during use may be harmful to your hands
and arms. Discontinue use of tool if
discomfort, tingling, or pain occurs. Seek
medical advice before resuming use.
PLEASE REVIEW ALL WARNING INSTRUCTIONS PRIOR TO OPERATION. SAVE ThIS mAN U AL fOR fUTURE REf ER ENCE.
6-1078
WARNING
• Compressed air can
cause severe injury.
Never direct air at
yourself or others.
Always turn off the
air supply, drain hose
of air pressure and
detach tool from air
supply before installing,
removing or adjusting
any part or accessory on
this tool, or before
performing any
maintenance on this
tool. Failure to do so
could result in injury.
Whip hoses can cause
serious injury. Always check for and
replace any damaged, frayed or loose
hoses and fittings. Do not operate a
damaged or worn tool. Do not use
quick-detach couplings at tool. See
instructions for correct set-up.
• Place the tool on the work before
starting the tool. Do not point or
indulge in any horseplay with this tool.
• Slipping, tripping
and/or falling while
operating air tools can
be a major cause of
serious injury or death.
Be aware of excess hose
left on the walking or work surface.
• Keep body working stance balanced
and firm. Do not overreach when
operating the tool.
• Anticipate and be alert for sudden
changes in motion during use of any
power tool.
• Do not carry tool by the
hose. Protect the hose
from sharp objects and
heat.
• Tool shaft may continue
to rotate briefly after
throttle is released. Avoid direct
contact with accessories during and
after use. Gloves will reduce the risk of
cuts or burns.
• Keep away from
rotating end of tool.
Do not wear jewelry or
loose clothing. Secure
long hair. Scalping can
occur if hair is not kept
away from tool and accessories.
Choking can occur if neckwear is not
kept away from tool and accessories.
• Impact wrenches are not torque con t rol
devices. Fas t en e rs with spe c if i c torque
re q uire m ents must be checked with
suit a ble torque measuring de v ic e s after
in s tal l a t ion with an im p act wrench.
• use only impact wrench sock ets
and ac ces so ries on this tool.
Do not use hand sock ets and
ac ces so ries, as they may be
damaged or cause damage to
the equipment or operator.
• Do not force tool beyond its rated
capacity.
• Do not remove any labels. Replace
damaged labels.
• Keep tool out of reach of children.
• Note direction of rotation BEFORE
operating this tool.
• Use accessories recommended by
NAPA Professional Air Tools.
• This product contains chemicals known
to the State of California to cause
cancer and birth defects or other
reproductive harm. Wash hands
thoroughly after handling.
2
• Do not lubricate tools
with flammable or volatile
liquids such as kerosene,
diesel or jet fuel.
• This tool is not insulated
against electric shock.
• Do not use (or modify)
the tool for any other
purpose than that for
which it was designed
without consulting the
manufacturer's authorized
representative.
• This tool must not be used
in explosive atmospheres.
Rev. 02/18/14