EdilKamin H2OCEANO 15 - 15/CS Instalación Uso Y Mantenimiento página 29

If combining with a pre-fabricated Edilkamin covering, to de -
ne the exact positioning of the thermo replace, it is important
to take the chosen covering model into consideration.
The positioning is implemented according to the model chosen
(refer to the installation instructions found inside the packaging
of each thermo replace covering).
Always ensure the thermo replace is level during the installa-
tion process.
- Drill a hole into the wall or the ooring for the external air
intake and connect the air adjustment mechanism to the hole as
described in the chapter called "external air inlet".
- Use a stainless steel ue to connect the thermo replace to the
chimney ue, adhering with the diameters indicated in the spe-
ci cations table and the guidelines given in the chapter called
"chimney ues".
- Verify that all moving parts function properly before setting
the thermo replace covering in place.
- This system must be tested and ignited for the rst time
before the covering is set in place.
INSTALLATION COVERING, FIREPLACE MAN-
TEL AND VENTILATION OUTLETS
The base of the thermo replace covering must allow the
internal air to be recycled. Therefore, suitable slots or apertures
must be made for the air to pass through. Parts of the thermo
replace covering that are made of marble, stone and bricks
must be mounted with a small gap between them and the re-
place so as to prevent possible breakage due to expansion and
excessive overheating.
Wooden parts must be protected by re resistant panels and
Practical advice
It is recommended to keep the radiators closed in the room
where the thermo replace is installed; The heat emitted from
the outlet may be suf cient to heat.
- An incomplete combustion process causes excessive fouling
on the heat exchanger pipe.
To prevent this you must:
- burn dry wood.
- ensure the hearth contains a bed of embers and burning car-
bon before adding more wood.
- place larger logs together with smaller ones.
- make sure the temperature of the return water is at least 50 °C
(use temperature control valve).
Igniting the replace
- Ensure that at least one radiator is always open.
- Actuate the switches of the electronic regulator.
- Place a pile of medium-thin dry wood in the thermo replace
and ignite the re.
- Wait a few minutes until it reaches suf cient combustion.
- Close the door
- Set the thermostat on the electronic regulator (*) at a tempera-
ture between 50 and 70° C.
NOTE: There may be a slight smell of paint the rst few times
it is ignited, however, this will disappear quickly.
(*) these components of the system are to be provided by the installer.
INSTALLATION
INSTRUCTIONS FOR USE
- 29
no part must touch the thermo replace, on the contrary, there
must be an appropriate distance of at least 1 cm to allow the
air to ow, preventing heat accumulation. The replace mantel
can be made of reproof plasterboard panels or gypsum board
and, however, of completely reproof material. Air should be
allowed to ow inside the replace mantel (through the gap
between the door and the beam). Through convective motion,
the air will ow out from the grille installed at the top, resulting
in heat recovery and preventing excessive overheating.
The replace mantel must have appropriate openings to carry
out maintenance on the ttings.
In addition to that mentioned above, please consider the in-
dications stipulated in the UNI 10683 standard, paragraphs
4.4 and 4.7: "insulation, nishing, replace covering and
safety recommendations".
Insulating mats must be applied when using an installation
KIT so as to protect it from the heat radiation emitted by
the thermo replace.
INLET FRAME (OPTIONAL)
To facilitate coupling with the covering's components, the ther-
mo replace can be tted with a frame (A) to be applied on the
front of the inlet.
A
3-way valve
- During ignition the 3-way valve (*) diverts the ow of water,
forcing it to return directly to the thermo replace;
when the set temperature is reached, the 3- way valve (*)
diverts the ow to the system (does not depend on the kit
installed).
By-pass damper
- When the door is closed, the by-pass damper automatically
diverts smoke, thus improving ef ciency.
- When the door is opened, the damper bypass opens automa-
tically, allowing the smoke to reach the smoke ue directly,
preventing it from coming out of the inlet.
Thermal Relief Valve
If the water temperature exceeds 90° C (e.g. because of too
much wood being placed in the hearth) the thermal relief valve
will be activated and the acoustic signal triggered.
In this case you must proceed as follows:
Do not load additional fuel and wait for the temperature to fall
below 80°C checking the warning lights on the electronic regu-
lator. The hot water tap can be opened to speed up the cooling
process if the thermo replace is equipped with a hot sanitary
water production KIT.
-
Plasterboard
A