Denon AVR-3802 Instrucciones De Operación página 13

_I , "t_ _ ;'_'_l'ill'_ I_ I
Once "Meter" or "Feet" s selected in Step 3,
the Delay T_me screen appears automat cally
Delay Time
I
Default _4
_Front L
Front R _6m
Canter _6m
Su_fer _6m
[]
Delay Time
43,0m_
3,0m
30m
3,0m
3,0m
&Om
• Use this setting to adjust so that the playback level between the different channels is equal
• Fromthe fistening position, listen to the test tones produced fromthe speakers to adiust thelevel
• The level can also be adjusted direcdy from the remote control unit (For details, see page 27 )
• When using both surround speakers A and B, their playback levels can be adjusted separately
5
Selectthe speakerto be set
Set the distance between the Delay Time
center speaker and listening
/
posdion_ _ i e_auit _
Pront L _6m
The distance changes in units _c_ R ,_6_
of g_l meters I1 foot) each l_entar _.em_i
time the button IS bressed_ _ti_ &6m
Select the value closest to the
measured distance_
E×_r_lr_i_ _l_r_ ti_ _a_¢_ _ _ _o
_f r'_sr' is selected for "Default", the se_ings are
automatically reset to the default values
Please note that the difference of distance for every speaker
should be 45 m (15 ft} or less If you set an nvalid distance,
a CAUTION notice, such as screen right will appear In this
case, please relocate the blinking speaker(s) so that its
distance is no larger than the value shown in highlighted line
Delay Tilde ]
_SL A 2
$R A _m
SL B _dlm
SR 5 3.0m
SBL 3.0m
SBR 3,0m
Front L 3,1_m
4
7
Enter the setting
The System Setup Menu reappears
The AVR-3802 automatically sets the optimum surround delay tree for the listening room
At the System Setup Menu select "Channel Level"
I System Setua Menu t
power _np Assilnment
Speaker Configuration
$B CH Auto Flal Detect
Oaley Time
_Dhannel Level
DIiItal In Assl|nment
Multi VoL Level
On Screen Display
Auto Tuner Presets
Switch to the Channel Level screen
Channel Level
u_rest Tone _:_
Surf, SO. _B A+8
Test Tone Start []4
Level Clear[_
Select "T_st Tune Mode"
Select the mode [- Channel Level
Select "Auto" Or "Manual" l[u'Te=t Tone _:;_
• Auto:
Adjust the level while listening to the test tones produced Surr" SI_ _B A+B
automatically from the different speakers
• Manual: Test Tone Start [_4
Select the speaker from which you want to produce tile Level Clear [_4
test tone to adjust tbe level Ex r_p_eWhe_ the /_ut_ r_odeiee ed
NOTES:
• If the distance unit is changed after the delay time is set, the setting° are reset to tee factory default values
(see page 9)
5
Select "Surf Sp", then select the surround speaker(s) from which
you want to produce the test tone (A, B or A+B)
• Surr Sp: A
Adjusts the balance of the playback level between the channels
when using surround speaker A
• Surr Sp: B
Adjusts the balance of the playback level between the channels
when using surround speaker B
• Surr Sp: A+B
Adjusts the balance of the playback level between the channels
when using surround speakers A and B at the same time
The "Sure Sp" can only be selected when both surround
speakers A and B have been selected at the "Speaker
Configuration" {when both A and B have been set to "Large" or
'*Small*')
Select "T_stTune Start"
13