Denon AVR-3802 Instrucciones De Operación página 14

8
Select "Y_s r'
Channel Level
Test Tone _:)_
Surf. S_ []_B A+B
_eat Tone Start [_4
Level Cle=r[_
a If the "Auto" mode is selected:
T_st tones are automatically emitted from the different
Whe_l you adjust the channe] levels while i_1the SYSTEM SETUP CHANNEL LEVEL mode, the chan_lel
level adiustments made will affect ALL surround modes Consider this mode a Master Channel Level
adjustment mode
After you have completed the SYSTEM SETUP CHANNEL LEVEL adjustments, you can then activate the
individual surround modes and adjust channel levels that will be remembered for each of those modes
Then, whenever you activate a particular surround sound mode, your preferred channel level adjustments
for just that mode will be recalled Check the instructions for adiust ng channel levels within each
surround mode on page 27
You can adjust the channel levels for each of the following surround modes: DIRECT, STEREO, 5/7 CH
STEREO, DOLBY/DTS SURROUND, WIDE SCREEN, ROCK ARENA, JAZZ CLUB, VIDEO GAME, MONO
MOVIE, and MATRIX
When using either surround speakers A or B, or when using surround speakels A and B at the same time,
be sure to adjust the balance of playback levels between each channel for the various selections of "A
or Br' and "A and B"
Ispkr ExamPe Vt/]en fie v°iu _e s se to
l _ I 12 dB w,hile the test 1o_1e
_s being produced _om _he
subw,oofe_
2spkrs
When the surround back speaker setting is set to
"lspkr"for"Speaker Configuration",thisis setto "SB"
Use the CURSOR buttons to adjust all the speakers to the
same volume
The volume can be adiusted between -12 dB and +12 dB in
units of 1 dB
b When the "Manual" mode is selected
ExarTip_e When _he vo_clme is set to
12 dB wMe the
subw,oote_ is selected
9 After the above settings are completed, press the ENTER button
The "Channel Level" screen reappears
Tu cancel the settings, select "Level Clear" and "Yes" on the "Channel Level" screen, then make the
settings again
The level of each channel should be adiusted to 7S dB (C-weighted, slow meter mode) on a sound level meter
at the listening position
If a sound level meter s not available adiust the channels by ear so the sound levels are the same Because
adjusting the subwoofer level test tone by ear is difficult, use a well known music selection and adiust for natural
balance
NOTE: When adjusting the level of an active subwoofer system, you may also need to adjust the subwoofer's
own volume control
• This setting assigns the digital input jacks of the AVR-3802 for the different input sources
At the System Setup Menu select "Digital In Assignment" _ System Setup Menu
Power Amp Assilnment
1
Spelker Confiluration
SB CHAuto FlaK Detect
Oelay Time
Channel Level
_DIiItal In Asel|nment
Multi ¥ol. Level
On Screen Di$pley
Auto Tuner Presets
2
Switch to the Digital In Assignment screen
Dllit_al.,_uJ:<_ln A SSl nment
OPTICAL1
OPTICAL2
[_] OPTICAL3
OFF
OFF
OFF
Oe_'auIt _4
Select the digital input jack to be assigned to the input source
a To select the ir_put source
a To select the digital input iack
Select "OFF" for input sources for which no digilal input jacks are used
If "Y_s" is selected for r'Default", the settings are automat cally reset
to the default values
Ente_ the setting
The System Setup Menu reappears
NOTES:
a The OPTICAL 3 jacks on the AVR-3802's rear panel are equipped with an optical digi[al output jack for
recording d gital signals on a CD recordeh MD recorder or other dig tal recorder Use this for dig tal recording
between a digital audio source (stereo - 2 channel) and a digital audio recorder
a Do not connect the output of the component connected to the OPTICAL 3 OUT jack on the AVR-3802's rear
panel to any jack other than the OPTICAL 3 IN jack
a "PHONO" and "TUNER" cannot be selected on the Digital In Assignment screen
14