WALMEC GENESI CARBONIO 360 HTE Clear Manual De Instrucciones página 28

Mod. EGO HVLP
TECHNICAL SPECIFICATIONS
- Air fitting: G 1/4" M
- Maximum air pressure: 5 bar (73 psi)
ø FEED ** PRODUCT LOAD
0.5 Gravity
0.7 Gravity
1.0 Gravity 66 Gr/min. (2.3 oz/min.)
1.2 Gravity
1.4
Gravity
** Product flow was calculated with water, setting the recommended regulations.
RECOMMENDED AIR PRESSURE DURING USE FOR EGO HVLP: 2 bar (29 psi)
At the recommended air pressure the spray gun respects the European and U.S. ecological norms for which the transfer effi-
ciency must be above 65% and /or the air pressure at the exit of the air cap must not be superior to 0,7 bar (10 psi).
USE
The EGO spray gun has been designed for touching up in the body shop and for graphics and decoration work with low fumes emis-
sion.The instrument is not suitable for use with abrasives or products containing acids or petrol of any kind.
To obtain the best results, the following instructions must be followed carefully:
1. When possible, use an air hose with a minimum internal section of ø 10 mm (0,37").
2. Make sure water, oil or other impurities are fully filtered from the compressed air used (for example, by installing a Walcom FSRD3/4
filter unit or the most complete and efficient Walcom TD3 PRO multifunction heat conditioner).
ADVICE FOR CORRECT USE
1. The distance between the spray gun and the surface to be painted must be set between 100-150 mm (3,9"- 5,9").
If the spray gun is working at too low a pressure and at too high a distance, it will not perform to the best of its capacity.
2. The jet from the spray gun must always be perpendicular to the surface being painted and the paint must be applied in horizontal
strokes. Any eventual shift from this position when spraying will result in an uneven application of the paint layer.
3. Correct viscosity of the paint is between 15 and 25 sec. Ford cup n°4.
These values depend on the application and the nozzle size used.
SHAPE OF THE FAN
- Air pressure too low
- Product viscosity too high
- Quantity of product too high
Adjust the air pressure, product quantity and spray aperture
until obtaining a regular imprint as in fig. C
istruzioni WI34_18.indd 28
ADJUSTMENTS
- Working pressure: 2 bar (29 psi)
- Fan: Fully open
- Air: Fully open
- Product : 3-4 turns
FAN DIMENSIONS AT 15 cm (5.9")
10 cm (3.9")
12 cm (4.7")
14 cm (5.5")
15 cm (5.9")
16 cm (6.3")
- Air pressure too high
- Product viscosity too low
- Quantity of product too low
28
AIR CONSUMPTION
140-180 l/min (4.7-6 CFM)
- Regular jet
09/01/18 14.18
SICH
• Vor Ge
durchl
• Die vo
BRAND
• Die Sp
(ATEX-R
• Keine
(Trichlo
Reaktio
• Alle Vo
• Sicher
• Antist
AUSST
• Währe
Augen
• Währe
für de
Produ
• Währe
dB(A)
• Die Sp
• Die An
Lösem
• Der G
Verletz
der de
GEFÄH
• Den S
• Die m
• Als Er
• Nach
ist sich
RISIKE
• Vor de
• Für die
werden
• Die Sp
• Nach
• Das G
Spritzk
HINWE
• Die Sp
• Den re
• Die Sp
der D
• Alle la
(der G
• Die Sp
den la
• Eine u