Nice Era Mat T Instrucciones Y Advertencias Para La Instalación Y El Uso página 15

4. The wind dies down and reaches the wind under-threshold; after about 10 minutes the wind alarm condition stops; at this point, if there is still the "raining" condition, the
rain sensor is reactivated and the preset manoeuvre is commanded.
5. When the sensor detects the "not raining" condition, it reactivates the "sun" sensor and, if the light intensity is over-threshold, the system opens the awning.
6. When the light intensity drops to the under-threshold, after about 15 minutes a raise manoeuvre is commanded.
6.2.2.5 - "Sun-On" and "Sun-Off" commands sent by the user
The user may activate ("Sun-On" ) or deactivate ("Sun-Off" command) the reception by the motor of automatic commands transmitted by the climate sensors present in the
installation. If at the time when the "Sun-On" command is sent the sunlight intensity is over-threshold, the system commands the opening of the awning; instead, if in that
moment the sensor is already activated, the system is reset and activates the sensor again, making the algorithms start again immediately.
If no manoeuvre is set when the "Sun-On" command is sent, the motor signals the reception of the command by performing 2 movements. If at that time the sunlight inten-
sity is under-threshold and does not allow the awning to be opened, the motor will command the closure of the awning, in accordance with this condition. In the conditions
to perform a manoeuvre are not met (e.g. because the awning is closed and it is not sunny), the motor will perform 2 movements to signal the reception of the command,
upon receiving the "Sun-On" command. By sending the "Sun-Off" command, the automatic movement of the awning is inhibited in connection with the sun phenomenon.
Therefore the automation will only work in the manual mode. Warning – The "wind" and "rain" sensors cannot be deactivated.
6.3 - Adjustment of "Wind" climate sensor
At the factory, the intervention threshold to is set at level 3 and to change it you must take the following steps:
Before starting the procedure, bring the awning to the midpoint of its stroke.
01. Keep the n key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
02. Keep the t key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
03. Briefly press the s key a few times, depending on the level you want to set for wind threshold:
• 1 press = wind at 5 Km/h • 2 presses = wind at 10 Km/h • 3 presses = wind at 15 Km/h (factory settings)( * )
• 4 presses = wind at 30 Km/h • 5 presses = wind at 45 Km/h
After about 10 seconds, the motor performs the number of movements indicated by the level number selected. Note – If this does not occur, cancel the procedure. this
way, the adjustment is completed without changing the factory setting.
04. Keep the n key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
01
5
sec.
03
x 1 = wind at 5 Km/h
x 2 = wind at 10 Km/h
x 3 = wind at 15 Km/h( * )
0,5
x 4 = wind at 30 Km/h
sec.
x 5 = wind at 45 Km/h
Notes • When performing the procedure, at any time you can cancel it by keeping the n and t keys pressed simultaneously for 4 seconds. Otherwise, do not press any
key and wait 60 seconds for the motor to perform 6 movements. • If you use a sensor equipped with a "trimmer", you must read the sensor instructions and adjust the
threshold directly on the sensor.
6.4 - Adjustment of "Sun" climate sensor
At the factory, the intervention threshold to is set at level 3 and to change it you must take the following steps:
Before starting the procedure, bring the awning to the midpoint of its stroke.
01. Keep the n key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
02. Keep the t key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
03. Briefly press the t key a few times, depending on the level you want to set for the intervention threshold:
• 1 press = 5 Klux • 2 presses = 10 Klux • 3 presses = 15 Klux (factory setting)( * ) • 4 presses = 30 Klux • 5 presses = 45 Klux
After about 10 seconds, the motor performs the number of movements indicated by the level number selected. Note – If this does not occur, cancel the procedure. this
way, the adjustment is completed without changing the factory setting.
04. Keep the n key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
01
5
sec.
03
x 1 = 5 Klux
x 2 = 10 Klux
x 3 = 15 Klux( * )
0,5 x 4 = 30 Klux
sec.
x 5 = 45 Klux
Notes • When performing the procedure, at any time you can cancel it by keeping the n and t keys pressed simultaneously for 4 seconds. Otherwise, do not press any
key and wait 60 seconds for the motor to perform 6 movements. • If you use a sensor equipped with a "trimmer", you must read the sensor instructions and adjust the
threshold directly on the sensor.
02
2
10
sec.
02
2
10
?
sec.
3
5
sec.
04
1 /
2 /
3 /
4 /
?
sec.
5 /
3
5
sec.
04
1 /
2 /
3 /
3
5
4 /
sec.
5 /
3
5
END
END
English – 14