Zoom Speed ; Auto Focus; Motion Det - Samsung SCC-C4201 Guia Del Usuario

CTRL TYPE : You can select the A, B, C, or D mode
depending on the input of the wired remote control terminal.
(See page 7.)
RS-485 : It sets up ADDRESS, PROTOCOL, and BAUD
RATE of RS-485 communication.
(BAUD RATE: 2400bps, 4800bps, 9600bps, 19200bps, 38400bps)
Caution : A communication error may occur if you connect
more than one camera set with an identical address.
PIP : This is the Picture in Picture feature. It will show a
screen reduced by 1/16 of the main screen only when
operating the Digital Zoom. If you set the PIP option to ON
and press the ENTER button, you can use the UP, DOWN,
LEFT, and RIGHT buttons to set the PIP position.
* The PIP feature does not work in a low speed shutter mode.
The MIRROR feature does not work on the PIP window.
(SPECIAL)
EANGUAGE ENGLISH
V-SYNC LINE...
CTRL TYPE A
RS-485 ...
PIP ON
MIRROR OFF
Press the
D-ZOOM OFF
POSI/NEGA +

ZOOM SPEED

3
DETAIL (0) ----I--
RET
MIRROR : Horizontally flips the video output signal.
D-ZOOM : Sets the magnification of the Digital Zoom.
The magnification level can be set to up to 10x.
POSI/ NEGA : Outputs the video output signal normally or
inversely.
ZOOM SPEED : In the ZOOM SPEED option, use the
LEFT and RIGHT buttons to set the speed as follows:
1 : Takes about 17 seconds from 1 x to 22 x magnification (slowest speed).
2 : Takes about 10 seconds from 1 x to 22 x magnification (slow speed).
3 : Takes about 6 seconds from 1 x to 22 x magnification (fast speed).
4 : Takes about 3 seconds from 1 x to 22 x magnification (fastest speed).
DETAIL: Adjusts the sharpness.
23
PIP
ENTER
button.

AUTO FOCUS

In the AUTO FOCUS option, you can specify the Focus
method to AF, MF, or ONEAF.
AF : Focuses automatically by continuously monitoring the
screen in AUTO FOCUS mode. It does not process the
FOCUS button input because it focuses automatically
during ZOOM.
MF : You can manually adjust
the focus.
ONEAF : Focuses about 5
seconds only when ZOOM is
moved Wide to Tele. It is same
as MF mode while in STOP
mode, and same as AF mode
after ZOOM Tele.

MOTION DET

In the MOTION DET option, you can set the Motion
Detection function, motion detection sensitivity, and the
motion detection area. If you set the Motion Detection
function, you can detect an intruder's movement and check it
through the monitor and the ALARM OUT terminal.
If you set ALARM which is located under COLOR/BW
AUTO menu to ON while MOTION DET remains ON, the
ALARM output port can not send any motion.
* MOTION detection function operates based on the
brightness change within the setup region. Therefore,
erroneous operation may occur depending on the brightness
difference between the background and the object that is
being taken, or the status of the area setup, etc.
(SET UP)
CAMERA ID OFF
IRIS ALC...
SHUTTER OFF
AGC LOW
WHITE BAL ATW
SPECIAL ...
Press the
AUTO FOCUS ONEAF
MOTION DET ON...
PRESET ...
COLOR/BW COLOR
EXIT QUIT
(SET UP)
CAMERA ID OFF
IRIS ALC...
SHUTTER OFF
AGC LOW
WHITE BAL ATW
SPECIAL ...
AUTO FOCUS AF
MOTION DET OFF
PRESET ...
COLOR/BW COLOR
EXIT QUIT
(MOTION DET)
ENTER
AREA PRESET...
button.
SENSITIVITY MEDIUM
RET
E
24