lamber PT-800-ek Manual Del Instrucciones página 23

First Section - FOR THE USER
WORKING AND USE
- When the objects to be washed present burnt crusts, or a long time is elapsed from cooking up to the time of washing,
it is necessary to make a previous softening in water at 50°C, by using an appropriate softeningproducts;
- Never deep naked hands in detergent water;
- While the machine is running, never open the door too rapidly;
- Only use specific anti-frothing detergents.
OPERATION BEFORE WASHING
B
EFORE STARTING THE WORKING OPERATION BE SURE
:
THAT
- the cock is open;
- the filters and the overflow are in
their housings;
- the wash arm and the rinse arm are
pivot;
- brightener and washing powder dispenser
containers are loaded.
T :
HEN PROCEED
A
- Put the detergent directly into the tank, by
paying attention to distribute it uniformly
on the filters, the quantity being according to
supplier's instructions.
N.B. When using chlorinated detergent, it is
suggested to use an automatic dispenser; if
otherwise, brownish spots might appear on the
surfaces, because of chlorine reactions, if
powering the detergent directly in the tank.
B
- Place the objects in the basket minding to
previously remove all solid waste and fat.
N.B.: When the objects to be washed present
burnt crusts, or a long time is elapsed from
cooking up tothe time of washing, it is necessary
to make a previous softening in water at 50°C,
by using an appropriate softening product.
C
- Turn the machines on by wall switch and
push the switch "A" situated in Dis.1.
At this moment the thermometer display lights up
And the tank fills up. When the tank is full the
control lamp for cycle "2" lights up.
D
– Introduce the basket in the ware-washer.
The control lamp "E" will flash in case the door of
the dishwasher is open.
Before you start the cycle be sure that the control
lamp "D" is flashing. This means that the water for
the washing cycle and the rinsing water
temperature reached the ideal temperature for
working.
E
the button "B" between the following items:
- lamp 1 flashing – short cycle of 1 minute
free to
- lamp 2 flashing – medium cycle 2 minutes
- lamps 1 and 2 lightening at the same time
long cycle of 3 minutes.
The washing period cycle has to be chosen
regarding the dirt that has to be removed.
F –
The dishwasher starts the washing with the
period you chosen. Additional to this period will
be a pause of 5 seconds and a rinsing period of
23 seconds with clean water about 85° to 90°C.
The control cycle lamp is flashing up to the end of
the complete washing period. Finished the
washing period the control lamps will stop
lightening.
Only for machines with steam condenser!
At the end of the washing, the steam suction fan starts
running automatically. The suction continues for a time
that can be programmed from 5 to 80 seconds after the
rinse end (as default 20'').
For the programming, look at the specific paragraph in
the installer section.
Cycle lamps flash till the completion of the final phase
of steam ventilation/suction.
At the end of the cycle, the lamps stop flashing and an
acoustic signal, with a maximum duration of one minute,
informs that it is possible to open the hood.
(Attention! During the cycle, at the hood opening also
the steam suction fan starts running for a maximum
time of 20 seconds).
It is possible to interrupt the washing cycle at any
time simply pushing again button "B".
The lighting of the control lamp "D" means that
the water reached the needed temperature of 85°
to 90°C.
The rinsing will start working of by the reached
temperature need. That means the period of the
23
– Choose the washing period cycle and push
Close the door of the ware-washer.
Push the button cycle "C"
ENGLISH