Way Manual Lock; Additional Information - Petsafe PPA19-16145 Guia De Inicio Rapido

The PetSafe Microchip Cat Flap is suitable to fit most doors or partitions although
®
additional materials and competent DIY skills may be required. This cat flap is
designed to adapt easily to cut-out sizes for Staywell 200, 300, 400, 500, 900
®
and Petporte smartflap series cat flaps. Some simple DIY skills are required and
®
minor adjustments to the cut-out or additional accessories might be needed.
Installation – Measurement and Marking
Measure the belly height of your Fig. A Fig. B
cat. This is usually
100 mm –150 mm (Fig. A).
Mark this measurement on the
(x)
outside of your door and draw a
(x)
straight horizontal line 168 mm
long (Fig. B).
Please keep in mind that this horizontal line will eventually be the bottom of
the hole you will cut in your door. The frame of the cat flap will be 25 mm
lower. If necessary, this line may have to be raised slightly to account for some
door designs.
Installation – Wooden, PVC, or uPVC Doors
Before beginning, please check if your
door has a metal core. If a metal core
Fig. D
Fig. C
or metal plate is found, please refer to
the Installation Metal and Metal Core
Doors section of this guide (on the
next page).
1. Attach the supplied Cutting
(X) (X)
Template to the outside of your
door in the correct position
ensuring that it is the right way up and level (Fig. C).
2. Drill four corner holes with a 12 mm diameter drill bit as marked on the
Cutting Template through the door. Please ensure the drill remains straight
and level.
4
petsafe.com
3. Using a jig or key-hole saw, cut along the dashed line as indiated on the
Cutting Template. (Fig. D).
4. Temporarily place both frames into the cutout. Level the
Fig. E
cat flap until it is in the proper position. On the outside,
use a pencil to mark screw holes through the holes on
the exterior frame (Fig. E). Remove the cat flap and drill
the screw holes with a 6mm drill (Fig. F).
5. Clean the area from any dust, dirt or debris.
Fig. F
6. Place the interior frame (with attached tunnel) into the
hole from the inside. Align the exterior frame to the
outside of the door. Three (3) different lengths of
screws have been provided with this cat flap. Select
the appropriate length. Using a manual screw driver,
screw the exterior frame through the holes in your
door to the interior frame.
Important: Do not cut the tunnel. Key Fig. G
components are contained within the tunnel and any
alteration to the tunnel will affect functionality.
7. When the installation of the cat flap is completed,
place the two blanking plugs over the screws on the
exterior frame. The cat flap is ready to use (Fig. G).
Installation – Glass Doors, Windows
or Walls
A mounting adapter and wall extension tunnels are available to complete
the installation of the cat flap into glass doors, windows, or walls. Please
visit www.petsafe.com to learn more about glass and wall installation and to
purchase these accessories.
Important: Working with glass is a skilled job and should be carried out
by a professional glazier. It is not possible to cut holes in toughened glass
or double glazed units except at the time of manufacture. Please consult
a glazier.
Installation – Metal and Metal Core Doors
Installation of the cat flap into a metal door or a door with a metal core plate
will require some modifications. The presence of metal can interfere with the
performance of the cat flap including a reduction in read range of the microchip.
If you experience poor performance you may need to purchase and install a
mounting adapter. Please visit www.petsafe.com for more information.
Basic Operation - Guide
FUNCTION BUTTON LED INDICATOR ACTION
ACTIVATION
Manual Press & Release Red - Solid for 5 Latch will unlock. Use 4-Way Lock
Mode seconds options for pet access.
Automatic Press & Release Green - Solid for 5 Latch will lock and will only
Mode seconds be activated by reading a
"programmed" microchip ID.
Learn Mode Press & Hold for Red – Solid for up to Cat flap will exit Learn Mode
5 Seconds until 60 seconds once microchip ID is programmed.
LED is activated Latch will unlock after successful
programming. Repeat for
additional cats.
Motion N/A Green - Solid for the Motion is detected outside and the
Sensor length of activation cat flap is looking for a microchip
to read.
Low Battery N/A Red - Flashes every Replace batteries soon.
10 seconds
Batteries N/A Green – 3 quick Cat flap will enter Automatic
Replaced flashes mode.
Factory Reset Press & Hold 15 Red - 5 quick flashes Cat flap will enter back into
Seconds until Automatic Mode and be locked.
LED is activated All programmed microchip IDs will
be erased from the memory.
Error N/A Red – Continuous Remove batteries, wait 30 seconds
quick flashing then replace batteries. If Red light
continues, contact the Customer
Care Centre. Latch will attempt to
unlock for cat flap to be used in
Manual Mode.
Accessories available online

4-Way Manual Lock

The 4-Way Manual lock allows you to control your cat's access in and out of
your home in either direction. Until your pet is thoroughly familiar with using the
cat flap, it is a good idea to anly use the 4-Way Manual lock in the In or Out
position only (Fig. H).
In or Out In only Out only Fully locked
Fig. H

Additional Information

For extended information on your PetSafe ® Microchip Cat Flap including glass
and wall installation, helpful training tips, and available accessories, please
visit www.petsafe.com to download the full product Installation Guide.
Important recycling advice
Please respect the Waste Electrical and Electrical Equipment regulations in your country. This equipment
must be recycled. If you no longer require this equipment, do not place it in the normal municipal waste
system. Please return it to where it was purchased in order that it can be placed in our recycling system. If
this is not possible, please contact PetSafe ® Customer Care Centre for further information.
Battery Disposal
Separate collection of spent batteries is required in many regions; check the regulations in your area
before discarding spent batteries. At the end of the product life, please contact one of our Customer Care
Centres to receive instructions on proper disposal of the battery. Please do not dispose of the battery in
household or municipal waste.
Compliance
Hereby, Radio Systems Corporation, declares that this Petporte smart flap ® is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC (R&TTE). Unauthorised
5