Hallde CC-32 Instrucciones De Uso página 6

Always clean the machine thoroughly immediately
after use.
First switch of the machine by setting the variable
speed control (A15/F7) to the "O" position and
then remove the power supply plug from the wall
socket alternatively turn off the mains switch.
Take all removable parts off of the machine base
(A16) and remove the sealing ring from the
groove on the inside of the lid (K), clean and dry
them thoroughly and then replace the sealing ring
in the groove.
Never wash light metal items in the dishwasher
unless they are marked "diwash".
All accessories marked "diwash" can be washed
in the dishwasher.
All cutting tools can be washed in the dishwasher.
Wipe the machine base with a damp cloth.
Never use sharp objects, scouring powder or
pads, or high pressure hoses.
Never leave the knife (F4) or cutting tools (A6-
A12) in a wet condition or on a stainless steel
bench when they are not being used, but dry them
thoroughly and always place them on the wall
rack (E) on the wall.
Perform the following
checks weekly.
Remove first the feeder (A5), any cutting tools
(A6-A12) and the ejector plate (A13),
alternatively, remove the lid (F2), knife (F4) and
bowl (F5).
Turn the speed variable speed control (A 15/F7)
to the "I" position and check that the machine will
not start.
Fit the feeder (A5), set the variable speed control
to the "I" position and then check that the machine
stops when the feeders handle (A3) is raised and
re-starts when the handle is lowered.
Set the variable speed control to the "I" position,
raise the feeders handle and check that the shaft
(A14) stops rotating within two seconds.
Fit the bowl (F5) and lid (F2) and set the variable
speed control to the "I" position and check that the
shaft (F6) stops rotating within two seconds after
the lid has been lifted and turned anti-clockwise as
far as it will go.
Remove the power supply plug from the wall
socket, alternatively turn off the mains switch and
then check that the electrical cable is in good
condition and has no cracks.
If the electrical cable is worn or damaged or
shows signs of cracking, or if any of the above
safety functions are not in good working order, a
service mechanic should be called in to make
repairs before the machine is taken back into
operation.
That the rubber feet of the machine are firmly
screwed into position.
That the knives and slicing plates are whole and
sharp.
Trouble shooting.
To eliminate the risk of damage to the motor, the
CC-32 is fitted with thermal motor protection that
automatically switches off the machine if the
temperature of the motor should become to high.
The thermal motor protection has automatic reset,
which means that the machine can be started
again when the motor has cooled down, which
usually takes between 10 and 30 minutes.
FAULT: The machine will not start or stops while
running and can not be re-started. ACTION:
Check that the power plug is properly inserted in
the wall socket or, alternatively, set the mains
switch to the "I" position. Check that the fuses in
the wall box for the premises have not blown and
have the correct ampere rating. Check that the
feeder (A5) is correctly fitted and that the feeders
handle (A3) has been lowered. Check that the
bowl (F5) and lid (F2) are correctly fitted. Wait for
up to 30 minutes and then try to start the machine
again. Call in a service mechanic for action.
FAULT: Low capacity or poor processing result
when using the feeder (A5).
ACTION: Select the right cutting tool (A6-A12).
Always use the ejector plate (A1 3). Check that the
knives and slicing discs are whole and sharp. Press
the food down losely.
FAULT: Low capacity or poor processing results
when using the bowl (F5).
ACTION: Separate the foods into smaller, evenly-
sized pieces, max. 3x3x3 cm. Process for a
shorter or longer period of time. Process a smaller
amount each time.
FAULT: The cutting tool cannot be removed when
using the feeder (A5). ACTION: Always use the
ejector plate (A13). Use a thick leather glove or
other glove that the blades of the cutting tool
cannot cut through and remove the cutting tool by
turning it clockwise.
Technical specification
Hallde CC-32.
TYPE OF PROCESSING: Slices, shreds, and/or
grates fruit, vegetables, dry bread, cheese, nuts
and mushrooms. Chops and grinds meat, fish, fruit,
vegetables and nuts. Mixes/blends sauces,
aromatic butter, mayonnaise, soups, dressing,
thickenings, desserts, etc.
USERS: Restaurants, shop kitchens, diet kitchens,
day care centres, retirement homes, catering
establishments, etc. preparing from 10 to 80
portions a day.
CAPACITY AND VOLUME: Processes up to 2
kg. per minute with the feeder depending on the
type of cutting tool and foods. Volume of the
feeder: 0.9 litres. Diameter of the feed tube: 53
mm. Gross volume of bowl: 3 litres. Net volume of
bowl with free-flowing liquid: 1.5 litres.
MACHINE BASE: Motor: 1000 W. 100-120 V,
Single phase, 50-60 Hz. 220-240 V, single
phase, 50/60 Hz. Thermal motor protection.
Transmission: maintenance free toothed belt.
Safety system: Two safety switches. Degree of
protection: IP34. Power supply socket: Earthed,
single phase, 10 A. Fuse in fuse box for the
premises: 10 A, delayed. Sound level: LpA
(EN31201): 76 dBA during cutting and 82 dBA
during chopping. Magnetic field: Less than 0.1
microtesla.
CONTROLS AND SPEEDS: Two speeds (H
2-S ) for perfect processing results in
PEED
connection with cutting and chopping. Automatic
speed setting (H A
ALLDE
whether the feeder or the bowl is fitted. During
cutting with the feeder the machine operates at
approx. 600 rpm, and during chopping with the
bowl approx. 1,500 rpm.
CUTTING TOOLS AND CHOPPING KNIFE:
The diameter of the cutting tools is 185 mm. The
diameter of the chopping knife is 170 mm.
MATERIALS: The machine base is made of alumi-
nium. The vegetable cutting attachment with
feeder: polyamide. Ejector plate: acetal. Cutting
tool discs: Robust acetal, polysulphone,
polypropylene or aluminium. Cutting tool blades:
Knife steel of the highest quality. Vertical cutter/
mixer attachment: Bowl made of stainless steel,
knife hub of acetal, knife blades of knife steel of
the highest quality, lid of polycarbonate §.
NET WEIGHTS: Machine base: 8.6 kg.
Vegetable preparation attachment complete but
excluding cutting tools: 1 kg. Cutting tools: approx.
0.4 kg average. Fast chopping attachment
complete but excluding knife: 1.4 kg.
NORMS: EU Machinery Directive 89/392/EEC
and EMC Directive 89/336/EEC.
ALLDE
-S ) that senses
UTO PEED