Astralpool LUMIPLUS PAR56 LAMP Manual De Instalación Y Mantenimiento página 2

ENGLISH
IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be
implemented for installation and start-up. Therefore, the installer as well as the user must read the instructions
before beginning installation and start-up.
Keep this manual for future reference.
To achieve optimum performance of the underwater LumiPlus PAR56 lamp, follow the instructions provided below:
1. VERIFY THE CONTENTS OF THE PACKING:
• PAR56 LED lamp
• Installation and maintenance manual
The 52596, 70339 and 43412 lamps do not need any control as they only emit monocolor light.
The 56001 and 43411 lamps do need control for colour change and sequences.
2. GENERAL CHARACTERISTICS:
This lamp has been designed to be used fully submerged in fresh water. It is a Class III electric apparatus with very
low safety voltage (12 V with alternating current). The lamp is class 116, in accordance with standard EN 50065.
The floodlamp complies with IPX8 degree of protection at a nominal immersion depth of 2 m.
This floodlamp complies with international safety standards for lights, especially the EN 60598-2-18 standard: LIGHTS
PART 2: SPECIFIC REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.
The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric compo-
nents which have been inserted or handled at locations other than its own premises.
3. INSTALLATION:
• To correctly light a swimming pool we recommend you:
Install a lamp in the range LumiPlus V1 every 20 m² of water surface.
Install a lamp in the range LumiPlus V2 every 25 m² of water surface.
Note: Recommendation valid for light coloured pools. In darker coloured pools or stainless steel pools we recommend
oversizing the proportion of lamps per m².
• It is the responsibility of the fitter to ensure that the area around the connectors is properly insulated.
• The connection boxes should be at least 2 m. from the edge of the swimming pool or water installation.
• The 230/12V transformer supplying the lamp, should be installed 3.5 m. from the edge of the swimming pool or
water installation.
• Conduits installed less than 3.5 m. from the swimming pool edge, should not be lined or covered in metal.
THE HOLES AT THE BACK OF THE V2 LAMPS (FIG. 1) SHOULD BE LEFT FREE WHEN ASSEMBLING
THE PROJECTOR, SO THAT WATER CAN FLOW INSIDE FOR OPTIMUM PERFORMANCE OF THE LAMP
4. ASSEMBLY:
After installation of the housing and the clamp, assemble the projector.
Follow these steps to assemble the PAR56 LED lamp in an underwater projector with an incandescent lamp:
1. Ensure that the lamp is NOT receiving voltage.
2. Remove the lamp unit and the part of the projector and place it on the edge of the swimming pool (this operation is
fully described in the projector manual) (Fig. 2).
3. Dismantle the parts of the projector required to remove the incandescent lamp (this operation is fully described in
the projector manual)(Fig. 3).
4. Loosen the two screws which electrically connect the PAR56 incandescent lamp (Fig. 4).
5. Place the PAR56 LED lamp electrically connecting it with the two connection screws (Fig. 5).
6. Assemble the projector in its initial position (this operation is fully described in the projector manual).
7. Connect the projector to the mains.
Note: In the LumiPlus V2 models it is essential that the direction of the lamp is adequate, situating "TOP" on the top
part of the projector.
MODELS AVAILABLE ACCORDING TO CHARACTERISTICS
LumiPlus V1
Monocolour RGB
52596 56001
• Bag of fastenings
• Warranty booklet
LumiPlus V2
Monocolour
43412 (white)
70339 (blue)
ATTENTION
2
RGB
43411