Optional Accessories - Makita DHS782 Manual De Instrucciones

MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed before
attempting to perform inspection or maintenance.
CAUTION:
Clean out the upper and lower guards
to ensure there is no accumulated sawdust which may
impede the operation of the lower guarding system. A
dirty guarding system may limit the proper operation which
could result in serious personal injury. The most effective
way to accomplish this cleaning is with compressed air. If
the dust is being blown out of the guards, be sure the
proper eye and breathing protection is used.
CAUTION:
After each use, wipe off the saw
dust on the tool. Fine saw dust may come inside the
tool and cause malfunction or a fire.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
T o maintain pro d u c t S A F E T Y an d R E L I A B I L I T Y ,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Adjusting 0° -cut or 45° -cut accuracy
This adjustment has been made at the factory. But if it is
off, you can adjust it as the following procedure.
1. L oosen t h e c lamping s c re w s on t h e f ront an d rear
o f t h e tool so t h at t h e be v el angle c an be c h ange d . S et
the stopper to - bevel angle position if you are
going to adjust -cut accuracy.
Fig.47: 1. S topper
2. Make t h e base perpen d i c ular or 4 5 ° to t h e c ir c ular sa w
blade using a triangular rule by turning the adjusting screw with a
hex wrench. ou can also use a square rule to adjust
Fig.48: 1. T riangular rule
Fig.4 9 : 1. Adjusting screw for
s c re w f or 4 5 ° angle
3. T ig h ten t h e c lamping s c re w s an d t h en make a test
c ut to c h e c k i f d esire d angle is obtaine d .
Adjusting the parallelism
CAUTION:
Keep the parallelism accurate.
Otherwise the circular saw blade may bite into the
guide rail and the damaged guide rail may cause an
injury.
This adjustment has been made at the factory. But if it is
off, you can adjust it as the following procedure.
1. S et t h e tool to t h e ma x imum c utting d ept h .
2. Make sure all le v ers an d s c re w s are tig h tene d .
Loosen the screws shown in the figure.
3.
While opening the lower guard, move the rear of
4.
t h e base so t h at t h e d istan c e A an d B be c omes e q ual.
Fig.50: 1. S c re w 2. Base
5. T ig h ten t h e s c re w s an d make a test c ut to c h e c k
t h e parallelism.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
C enter.
•
•
•
•
•
•
•
•
•
angle.
angle 2. Adjusting
22 ENGLISH
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual. The use of any other
a c c essories or atta c h ments mig h t present a risk o f
injury to persons. Only use accessory or attachment
f or its state d purpose.
C ir c ular sa w bla d e
Rip fence (Guide rule)
H ook
G ui d e rail
Be v el gui d e
C lamp
S h eet
R ubber s h eet
P osition s h eet
Dust nozzle
H e x w ren c h
Wireless unit (for D S
Makita genuine battery and charger
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
)