Publicidad
OBJ_BUCH-0000000250-001.book Page 17 Tuesday, February 9, 2016 9:37 AM
Handling the battery.
Operate and charge the battery only within the battery
operating-temperature range of 0°C – 45°C (32°F –
113°F). At the beginning of the charging procedure, the
battery temperature must be within the battery operat-
ing-temperature range.
LED
Meaning
indicator
1 – 4 green
Percentage of
LED
charge condi-
tion
Continu-
Battery is
ous red
almost empty
light
Red flash-
Battery is not
ing light
ready for
operation
The real percentage of the battery charge condition is
only indicated when the power tool motor is stopped.
The electronics automatically switch off the motor prior
to the battery being deep discharged.
Additional operating instructions.
Do not actuate the clamping lever while the power
tool is running. Otherwise there is danger of injury.
Do not operate the power tool with with open clamp-
ing jaws and without an application tool! This could
damage the power tool.
When the clamping jaws are open before the appli-
cation tool is inserted, pivot the clamping lever
toward the front and then back again. The clamping
jaws are closed now. The application tool can be
inserted.
Guide the power tool toward the work piece only
when switched on.
The application tool can be offset in 30° steps and fas-
tened in the most favourable working position.
The self-start prevention lock prevents the power tool
from automatically starting when the battery is inserted
while the on/off switch is set to on.
Notes on sanding.
Press the power tool with the sanding sheet briefly and
firmly against a flat surface and briefly switch the power
tool on. This provides for good adhesion and prevents
premature wear.
When only one tip or corner of the sanding sheet is
worn, it can be removed again and reattached turned by
120°.
Work with the entire surface of the sanding plate, not
only with the tip.
When sanding with small triangle sanding plates, select a
high oscillating frequency (electronics level 4 – 6); when
sanding with the round sanding plate and the large trian-
gle sanding plate, select a moderate oscillating frequency
(max. electronics level 4).
Sand with continuous motion applying moderate pres-
sure. Applying excessive pressure does not increase the
rate of removal, it only wears off the sanding sheet faster.
Notes on sawing.
Select a high oscillating frequency. Round saw blades can
be released and clamped offset again, to allow for uni-
form wearing off.
Notes on scraping.
Select a moderate to high oscillating frequency.
Activity
Repair and customer service.
Operation
Blow out the interior of the power tool via the ventila-
Charge battery
tion slots frequently with dry and oil-free compressed air.
For storage of the power tool, remove the application
tool and shut the clamping lever.
Bring the battery into
The current spare parts list for this power tool can be
the battery operating-
found in the Internet at www.fein.com.
temperature range, then
If required, you can change the following parts yourself:
charge
Application tools
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's warranty declaration.
The delivery scope of your power tool may include only
a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH,
C-DB_IA, D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories should
be sorted for environmental-friendly recycling.
Dispose of batteries only when discharged.
For batteries that are not completely discharged, insulate
the terminals with tape as a protective measure against
short-circuiting.
When working metal under extreme operat-
ing conditions, it is possible for conductive
dust to settle in the interior of the power tool.
en
17
Publicidad
