Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
|
KEY DIMENSIONS
AND SPECIFICATIONS
Description
Rated Voltage/Frequency
Dimensions
Net "vVeight
Top-Loading
Washer
120VAC, 60Hz
27"(W)
X 28 3/8"(D)
X 41 3/10"(H),
55 3/8"(H
with lid open)
68.6 cm (W) X 72.1 cm (D) X 105.0 cm (H), 140.6 cm (H with lid open)
137.8 Ibs. (62.5kg)
CHOOSE THE PROPER LOCATION
WARNING
* Washeris heavy. Two or more people are required when
moving and unpackingthe washer. Failureto do so may
result in damage to property or serious bodily harm.
* Storeand install the washer where it will not be exposed
serious injury, fire, electric shock, or death.
warning can cause serious injury,fire, electric shock,or
death.
• To reducethe risk of electricshock,do not install the
washer in humid spaces.Failureto follow this warningcan
cause seriousinjury, fire, electric shock, or death.
• To ensure properair flaw, do not block the large opening
on the bottom of the washer with carpeting or other
materials.
' Do not remove ground prong. Do not usean adapter or
extensioncord. Pluginto a grounded3-prongoutlet. Failure
to follow this warning can cause serious injury, fire, electric
shock,or death.
NOTE: Installingthe washer in a humidspace, or installing or
storing the washer where it will be exposed to the weather or
freezing temperatures, may result in rust or other damage that
is not covered by the product warranty.
Power Outlet
' The poweroutlet must be within 60 in. (1.5 m) of either side
of the washer.
' The appliance and outlet must be positioned sothat the plug
is easily accessible.
• Do not overload the outlet with more than
one appliance.
• The outlet must be grounded in accordance with current
wiring electric codes and regulations.
• Time-delay fuse or circuit breaker is recommended.
NOTE: It isthe personal responsibility and obligation of the
product owner to have a proper outlet installecl by a qualified
servicetechnician.
FLOORING
• To minimize noiseand vibration, the washer MUST be
installed on a solidly constructed floor. See the NOTE to your
right.
• Allowable slope under the entire washer is a maximum I in.
difference from side to side or from front to back.
° Installing on carpeting
and soft tile surfaces is
not recommended.
• Never install the washer on a platform or weakly
supported
structure.
CLEARANCES
7
4! 3/_o"
(105.0 cm)
f
1"
___
27 ,_
_
!"
(2_5cm) -_
(68.6 cm)
(2 5cm}
Toensuresufficient clearance for water lines and airflow, allow
minimumclearances of at least 1 in.(2.5 cm) at the sides and
4 in.(10 cm) behind the unit. Be sureto allow for wall, door, or
floor moldings that may increase the required clearances.
32"
(81.1 cm)
28 3is"
[}1_:
(72.1 cm)
I
55 3/s'
(140.6 cm)
(with open rid)
26
3/4"
(68 cm}
3 !/2"
(9 cm)
Minimum
vertical
space from floor to overhead
shelves, cabinets, ceilings, etc., is 56 in.
NOTE: The washer must be installed on firm flooring
to minimize vibration during the spin cycle. Concrete
flooring
is best, but a wood floor is sumcient, provided
it is built to FHA standards. The washer should not be
installed on rugs or exposed to weather.
Publicidad
Capítulos
Tabla de contenido
