Denon AVR-3802 Instrucciones De Operación página 24

ENGLISH
Playback using the external input (EXT. IN) jacks
1
Set the external input (EXT. IN) mode.
Press the EXT. IN to switch the external input.
EXT.IN
EXT.IN
(Main unit) (Remote control unit)
Once this is selected, the input signals
connected to the FL (front left), FR (front right),
C (center), SL (surround left), SR (surround
right), SBL (surround back left) and SBR
(surround back right) channels of the EXT. IN
jacks are output directly to the front (left and
right), center, surround (left and right)
surround back (left and right) speaker systems
as well as the pre-out jacks without passing
through the surround circuitry.
In addition, the signal input to the SW
(subwoofer) jack is output to the PRE OUT
SUBWOOFER jack.
2
Cancelling the external input mode
To cancel the external input (EXT. IN) setting,
press the input mode (AUTO, PCM, DTS) or
ANALOG button to switch to the desired input
mode. (See page 23.)
AUTO PCM DTS ANALOG
MODE
(Main unit) (Remote control unit)
• When the input mode is set to the external input
(EXT. IN), the play mode (DIRECT, STEREO,
DOLBY/DTS SURROUND, 5/7CH STEREO, WIDE
SCREEN or DSP SIMULATION) cannot be set.
24
B
2 1
6.1 / 7.1
DIRECT STEREO
SURROUND
2 INPUT
MODE ANALOG EXT.IN
SYSTEM CALL
and
CALL 1 CALL 2 BACKLIGHT
NOTES:
• In play modes other than the external input
mode, the signals connected to these jacks
cannot be played. In addition, signals cannot be
output from channels not connected to the input
jacks.
• The external input mode can be set for any input
source. To watch video while listening to sound,
select the input source to which the video signal
ANALOG
is connected, then set this mode.
After starting playback
[1] Adjusting the sound quality (TONE)
The tone control function will not work in the Direct mode.
1
The tone switches as follows each time the
TONE CONTROL button is pressed.
TONE
CONTROL
(Main unit)
2
With the name of the volume to
be adjusted selected, turn the
1
SELECT knob to adjust the level.
• To increase the bass or treble: Turn the control
clockwise. (The bass or treble sound can be
increased to up to +12 dB in steps of 2 dB.)
• To decrease the bass or treble: Turn the
control clockwise. (The bass or treble sound
can be decreased to up to –12 dB in steps of
2 dB.)
[2] Listening over headphones
1
Connect the headphones to
the PHONES jack of the front
panel.
2
Press the OUTPUT button to play the sound
over the headphones only.
OUTPUT
• The output to the speaker and pre-out jacks is
turned off and no sound is produced from the
speakers.
Caution: Switching off the power of the unit and
the unit will cancel the settings.
[3] Turning the sound off temporarily (MUTING)
1
Use this to turn off the audio
output temporarily.
Press the MUTING button.
Cancelling MUTING
mode.
Press the MUTING button again.
B
BASS TREBLE
SELECT
(Main unit)
3
If you do not want the bass and treble to be
adjusted, turn on the tone defeat mode.
TONE DEFEAT
(Main unit)
PHONES
B
1
1
NOTE:
TV/ 0 +10
VCR
To prevent hearing loss, do not raise the volume level
RDS PTY RT 2
TEST
SPEAKER OUTPUT
TONE
excessively when using headphones.
SURROUND
DOLBY/DTS DSP 5CH / 7CH
SURROUND SIMU. STEREO
MUTING
(Remote control unit)
3 2 1
The signals do not pass
through the bass and treble
adjustment circuits, providing
higher quality sound.
TUNING
+
+
SKIP
ENTER
-
-
SHIFT
SKIP MUTING
1
TUNER PHONO CD
1 2 3