Preface; Introduction; Identification Of The Product; General Description - PLYMOVENT MDB-2 COMPACT Manual De Instalación Y De Uso

PREFAcE

Using this manual
This manual is intended to be used as a work of reference for
professional, well trained and authorised users to be able to
safely install, use, maintain and repair the product mentioned
on the cover of this document.
Pictograms and symbols
The following pictograms and symbols are used in this manual:
TIP
Suggestions and recommendations to simplify
carrying out tasks and actions.
ATTENTION
A remark with additional information for the user.
A remark brings possible problems to the user's
attention.
cAUTION!
Procedures, if not carried out with the necessary
caution, could damage the product, the workshop or
the environment.
WARNINg!
Procedures which, if not carried out with the
necessary caution, may damage the product or
cause serious personal injury.
cAUTION!
Risk of electric shok.
WARNINg!
Fire hazard! Important warning to prevent fire.
WARNINg!
Explosion hazard! Important warning to prevent
explosions.
Personal protective equipment (PPE)
Instruction to use respiratory protection when you
do service, maintenance and repair jobs, as well as
during functional testing. We recommend to use a
half-face respirator according to DIN EN 141/143,
protection class P3.
Personal protective equipment (PPE)
Instruction to use protective gloves when you do
service, maintenance and repair jobs.
Text indicators
Listings indicated by "-" (hyphen) concern enumerations.
Listings indicated by "•" (bullet point) describe steps to
perform.
Service and technical support
For information about specific adjustments, maintenance or
repair jobs which are not dealt with in this manual, please
contact the supplier of the product. He will always be willing to
help you. Make sure you have the following specifications at
hand:
- product name
- serial number
You can find these data on the identification plate.
Product indications
Product type
MultiDust Bank COMPACT (all types)
MultiDust Bank-2/COMPACT
MultiDust Bank-4/COMPACT
MultiDust Bank-6/COMPACT
0000104046/150915/0 MultiDust Bank COMPACT
Equals to:
MDB-COMPACT
MDB-2/C
MDB-4/C
MDB-6/C
1

INTRODUcTION

1.1

Identification of the product

The identification plate contains, among other things,
the following data:
- product name
- serial number
- supply voltage and frequency
- power consumption
1.2

general description

The MDB-COMPACT is a filter unit with integrated fan, cleaning
system and dust drawer for connection to an external device,
e.g. a welding robot or a cutting table. The fan is placed in a
sound absorbing box; to enhance noise reduction the fan
exhaust faces down. The unit is controlled by a separate
control panel (FilterControl).
Filter cartridges and fan control equipment are not included
and must be selected and ordered separately.
1.3

Product combinations

To operate the unit, selection of filter cartridges is required.
The following types are available:
Type Filter material
CART-D 100% BiCo polyester (15 m² / 161 ft²)
CART-C 100% Bico polyester with aluminium coating
(antistatic) (15 m² / 161 ft²)
CART-E PTFE impregnated BiCo polyester (15 m² / 161 ft²)
CART-PTFE/10 100% BiCo polyester with PTFE membrane (10 m² /
108 ft²)
CART-PTFE/15 100% BiCo polyester with PTFE membrane (15 m² /
161 ft²)
CART-MB 80/20 cellulose/spunbond polyester fibre with
polyester nanofibre overlay (10,7 m² / 115 ft²)
The specific product type (2/4/6) corresponds with the
required number of filter cartridges.
1.3.1 Precoat
To enhance the efficiency and lifespan of the filter cartridges, it
is strongly recommended to add precoat material (PRECO-N).
This applies to polyester filter cartridges type CART-D and
CART-C only.
Dosing per filter cartridge: 500 g (1.1 lbs.).
1.4

Options and accessories

The following products can be obtained as an option and/or
accessory:
1
Type Description
CAR-KIT Compressed air regulator
- Compressed air sensor (kit)
SparkShield Cyclonic spark arrester
PRECO-N Precoat material; refer to section 1.3.1
Adapter� Adapter from Ø 250 mm to Ø 10 in.
Adapter from Ø 400 mm to Ø 16 in.
Frequency inverter VFD-2.2 / Frequency inverter 2,2 kW (3 HP)
(refer to section
VFD-4 / Frequency inverter 4 kW (5 HP)
1.4.1)
VFD-5.5 / Frequency inverter 5,5 kW (7.5 HP)
VFD-11 / Frequency inverter 11 kW (15 HP)
Start/stop device To be sourced locally; refer to section 4.6.2
1. An adapter from Ø 355 mm to Ø 14 in. is not necessary.
EN - 3