Technical Data; Suitability For Use - KRATOS SAFETY FA 60 019 00 Manual De Instrucciones

This notice must be translated (possibly by the retailer) into the language of the country of use.
For your safety, comply strictly with the instructions for use, verification, maintenance and storage.
KRATOS SAFETY cannot be held liable for any direct or indirect accident occurring as a result of use other than provided for in this notice; do not use
this equipment beyond its capabilities!
USE AND PRECAUTIONS: A toggle anchor is a temporary, transportable anchoring point designed for use on horizontal
steel or concrete (only for FA 60 019 01) surfaces. It must be installed on surfaces capable of withstanding stresses exerted by
the anchor point itself in case of a fall: R>12kN. Stresses must be directed vertically and downwards. The drilling diameter for
installing the Toggle Anchor must be no greater than 22-23 mm. The hole must be drilled all the way through to let the toggle
tip up freely. The maximum thickness of the receiving structure must be: FA 60 019 00: 40 mm and FA 60 019 01: 330 mm.
Requirements for the receiving structure
Thickness:
Steel
Space around all edges:
Pre-cast concrete Thickness:
35 MPa Space around all edges:
In all cases, the structure must be the right size for the resistance
of the anchoring point: R> 12 kN.
Installation:
Push the anchor D-ring via the push button (fig. 1), the end toggle rotates to a parallel
position to the stem. Insert the stem in the bolt hole of the anchoring structure (fig. 2).
Release the push button, the toggle automatically returns to perpendicular position,
thus preventing the anchor point from going out of the anchoring structure (fig. 3).
Check the stability of the system by making a pressure in the direction in which the
strength will be applied during the use.
It is essential to make sure that the toggle is properly installed (fig. 3):
 If you can visually access the toggle, perform a visual inspection.
 In any case, make sure the security indicator is visible before using the anchor
point. If the green ring is not visible, a slight push on the anchor D-ring should
release the toggle. If the green ring is not visible, the product must not be used.
Green ring is visible = OK
This anchor point is a piece of personal protection equipment against fall from a height; it should be allocated to a single user.
It is recommended that the installation of this anchor point be supervised by a qualified person.
In all cases, connections between the anchor D-ring and the fall arrest system will have to be made through a connector (EN362). During the use, please
check regularly that the connector is correctly closed.
The anchor point should be installed so that the fall arrest system is situated above the user. Make sure that the work is done in such a way as to limit
the pendulum effect, as well as the risk and the height of a fall. For safety reasons and before each use, make sure that in the event of a fall there is no
obstacle obstructing the normal deployment of the fall arrest system fixed on this anchor point.
User safety relies on the effectiveness of the equipment and full understanding of the safety instructions contained in this leaflet.
Product markings should be checked periodically for legibility.
Before and during use we advise you to make the necessary, arrangements for a safe rescue if the need should arise.
This equipment is for the use of people trained, skilled and in good health, or under the supervision of a trained and skilled person. Warning! Certain
medical conditions may affect user safety; if in doubt, consult your doctor.
Be aware of the hazards that could reduce the performance of your equipment, and therefore the user's safety, if exposed to extreme temperatures (<
-30°C or > 50°C), prolonged exposure to the elements (UV rays, humidity), chemical agents, electrical constraints, twisting of the fall arrest system
during use, sharp edges, friction or cutting, etc.
Before each use, check that the toggle anchor has no traces of deformation or
toggle, the latter should vanish and automatically return in position. In case of doubt, the product should not be used anymore without a full checking
by a qualified person.
Do not remove, add or replace any component of the product whatsoever.
Chemical products: put the system out of use if it comes into contact with chemical products, solvents or fuels which could affect its workings.

TECHNICAL DATA:

Steel and steel treated against corrosion. Weight: 0.55 kg (FA 90 019 00) – 1.25 kg (FA 60 019 01).
KRATOS SAFETY certifies that the Toggle Anchor has been tested in accordance with the standard EN795:2012 Type B.

SUITABILITY FOR USE:

A fall arrest harness (EN361) is the only body gripping device that may be used. It may be dangerous to create one's own fall arrest system where each
safety function can interfere with another safety function. Therefore, it is important to read the recommendations on using each component in the system
before use.
VERIFICATION:
The recommended service life of the equipment is 10 years (in accordance with the annual examination by a competent person authorized by KRATOS
SAFETY), but it may be increased or reduced according to use and/or the results of the annual inspections. The equipment should be inspected if there is
any doubt, or following a fall and at least annually, by the manufacturer or a competent person authorised by the manufacturer to check its strength and
hence the user's safety. The product data sheet should be completed (by writing) after each verification; date of inspection and date of next inspection
1
Min: 5 mm
2
Min: 3 cm
Min: 11 cm
3
Min: 16 cm
4
5
Green ring is not visible = Warning! Do not use the toggle anchor!
oxidation.
5
Anchor D-ring
Toggle
Tube
Push button
Security indicator (green ring)
Pay a particular attention to the attachment D-Ring and to the
EN