Tractel travflex 2 Manual De Instalación página 19

d AP
100428 K/A/E
100438 K/A/E
100448 I
100458 I
100468 K/A/E
100478 K/A/E
100488 I
100498 I
100508 K/A/E
100518 K/A/E
100528 I
100538 I
d : Product code marked on label (fig. 15, item 10)
AP : Type of anchor compatible with plate
K: Ringflex anchor ring
A: End anchor used with travflex™ 2 lifeline
E: Intermediate anchor used with travflex™ 2 lifeline
I: Turn anchor used with travflex™ 2 lifeline
o : Minimum breaking strength of plate marked on label (fig. 15, item 10)
TB : Steel roof deck section: (number of ribs) x (length of rib)
J : Number of gaskets made of cellular rubber
R : Number of rivets
"Note": If rivets are lost during installation, additional rivets can be obtained on request by bag of 50 rivets:
code 100548: 50 aluminium rivets, dia. 7.7 mm.
V : Number of self-drilling and tapping stainless steel screws equipped with sealing washer required for reinforcement of roof
deck section fastening on support structure (section).
"Warning" : The self-drilling and tapping screws are not supplied with the mounting plates; these are available on
"Danger" : The self-drilling and tapping screws are indispensable to ensure the mechanical strength of the system
Fig. : Number of figure for installation of self-drilling and tapping screws (fig. 14, item 7)
Y (mm) : Width of mounting plate (fig. 15)
Z (mm) : Length of mounting plate (fig. 15)
T (mm) : Thickness of mounting plate (fig. 15)
MS
: Specification of material of mounting plates (fig. 15, item 1)
G: Plate made of galvanised steel
S: Plate made of stainless steel
P : Weight in kg
o TB
15 kN / 3372 lbs 8 x 125
15 kN / 3372 lbs 8 x 125
20 kN / 4496 lbs 8 x 125
20 kN / 4496 lbs 8 x 125
15 kN / 3372 lbs 4 x 250
15 kN / 3372 lbs 4 x 250
20 kN / 4496 lbs 4 x 250
20 kN / 4496 lbs 4 x 250
15 kN / 3372 lbs 3 x 333
15 kN / 3372 lbs 3 x 333
20 kN / 4496 lbs 3 x 333
20 kN / 4496 lbs 3 x 333
request in bags of 50 screws:
code 100558: 50 self-drilling and tapping screws for installation on support structure (section) with
thickness of between 1 mm et 3.5 mm.
code 100638: 50 self-drilling and tapping screws for installation on support structure (section) with
thickness of between 4 mm et 12 mm.
fastening the roof deck section to the support structure. Failure to use the self-drilling and tapping
screws will release Tractel ® of any responsibility.
J R V
(fig. 14, (fig. 14, (fig. 14,
item 5) item 6) item 7)
4 8 5
4 8 5
4 12 8
4 12 8
3 6 6
3 6 6
3 12 8
3 12 8
3 6 6
3 6 6
3 12 9
3 12 9
Y Z T
Fig.
(mm) (mm) (mm)
7 250 430 3
7 250 430 3
8 275 430 4
8 275 430 5
9 250 550 3
9 250 550 3
10 275 550 4
10 275 550 5
11 250 716 3
11 250 716 3
12 275 716 4
12 275 716 5
P
MS
(kg)
G 2.5
S 2.5
G 3.4
S 4.4
GB
G 3.2
S 3.3
G 4.6
S 5.8
G 4.2
S 4.3
G 6.0
S 7.6
19 19