Forward Movement; Stop; Stop Of The Machine After Cleaning Operation; Maintenance - ADIATEK ruby 50e Manual De Uso Y Mantenimiento

GB
ATTENTION:
This operation must be carried out using gloves to
protect from contact with dangerous solutions.

FORWARD MOVEMENT

The traction of these machines is given by the brush
that, working on an inclined axle, transmits to the
machine the forward movement.

STOP

Releasing the lever of the presence, the brush rota-
tion will end, stopping the machine movement.
ATTENTION:
Whenever moving the machine backwards, make
sure that the squeegee is lifted.
STOP OF THE MACHINE AFTER
CLEANING OPERATION
Before executing any type of maintenance:
1. Lift the squeegee acting upon the lever (8).
2. Turn the brush motor switch off (1).
3. Turn the suction motor switch off (2).
4. For machines equipped with key switch (see un-
der "OPTIONAL ACCESSORIES"), turn the key (6)
counterclockwise to switch off the machine.
5. Take off the plug from the mains socket.
6. Rotate backwards the machine so to lift the
brush base. With the right balance on the wheels,
bring the machine to an appropriate place for tanks
draining.
ATTENTION:
The machine is not equipped with a parking brake,
therefore do not leave it on slopes.

MAINTENANCE

RECOVERY TANK CLEANING

1. Hold the exhaust hose placed in the front part of
the machine.
2. Take off the exhaust plug acting upon its lever
and empty the recovery tank into appropriate con-
tainers (see under "OVERFLOW DEVICE").
3. Take off the suction cover (17) after rotating the
blocking levers (A).
4. Take off the filter and filter protection.
5. Rinse the tank with a water jet.
ATTENTION:
This operation must be carried out using gloves to
protect from contact with dangerous solutions.

SUCTION FILTER CLEANING

1. Take off the suction cover (17) after rotating the
blocking levers (A).
2. Take off the filter and filter protection.
3. Clean all parts with a water jet especially inside
surfaces and filter bottom.
4. Carry out carefully the cleaning operations.
5. Reassemble all parts.

BRUSH CLEANING

Disassemble the brush and clean it with a water jet
(for the brush disassembly, check "BRUSH DISAS-
SEMBLY" paragraph).

MANUAL BRUSH DISASSEMBLY

ATTENTION:
Check that the plug is disconnected.
1. Take off the squeegee.
2. Lift the support raising the lever.
3. Rotate backwards the machine until it rests on
the support wheels, so to lift the brush base.
19
4. With the brush base in lifted position, rotate the
brush energically, until the button is released from
the coupling spring and the brush comes off.
The figure shows the rotating sense for brush release.
ATTENTION:
The execution of brushes disassembly operations
with electric supply on, may cause damages to hands.

AUTOMATIC BRUSH DISASSEMBLY

For the automatic brush disassembly proceed as fol-
lows:
1. Check that there is electric connection.
2. Rotate backwards the machine so to lift the
brush base until the brush itself does not have any-
more points of contact with the floor.
3. Press the brush motor switch.
4. Act with an impulse upon the levers, so that the
buttons of the brush are released from its plate seat.
ATTENTION:
The handling of the brushes operation must be car-
ried out using suitable gloves to protect both me-
chanically from contact with the bristles and the
chemical risk of contact with dangerous solutions.

SQUEEGEE CLEANING

Keeping the squeegee clean guarantees always the
best drying action.
For the cleaning it is necessary to:
1. Take off the squeegee hose (A) from the coupling.
2. Disassemble the squeegee from the support ro-
tating the lever (B) counterclockwise sliding the stud
bolts (C) in their slots.
3. Clean with care the internal part of the squeegee
inlet eliminating eventual dirt residuals.
4. Clean with care the squeegee rubbers.
5. Reassemble all parts.
GB