Elko EP iNELS RFPM-2M Manual De Usario página 11

RFPM-2M
Energy gateway
EN
Settings - set RFPM-2M
Network interface settings
Network setup - RFPM-2M can be set as:
• Access Point Bridge – RFPM-2M is an Ethernet cable connected to a
home router that assigns IP to all devices that connect to RFPM-2M.
• Access Point LAN – RFPM-2M creates a custom network that is separate
from the home network. Devices can only be accessed from this
network. To connect to this network, it is necessary to confi gure the
static IP on the connected device.
• Client LAN – RFPM-2M is connected to a home router using DHCP or
static IP. RFPM-2M acts as a terminal device and cannot be accessed
directly through it.
To create a WLAN with AP Bridge / LAN, it is necessary to select Encryption
(none / WPA-PSK1 / 2) to enter a password that corresponds to the standard
of the given encryption (min. 8 characters). When the changes are saved,
the WLAN becomes visible.
DHCP enabled - Network settings
• –IP address is set automatically
• – IP address needs to be set in the appropriate range of the connected router (fi lling the IP address of RFPM-2, masks, gateways and DNS).
WLAN Access Point Settings - WiFi network setup RFPM-2M
• ESSID – the name of WiFi created
• Encryption – type of security
• Password – must be fi lled in the required form for that security
• Channel – WiFi broadcast channel
Setting the meters
External setup - external input S0
• Name – RFTM-1 name optionally chosen
• Unit – Unit of measurement (kW / h - for electricity measurement or m
for water or gas measurement)
• Pulses – Pulse value for the measured value (the value that translates the
number of pulses per unit of a given quantity) - this is given on the meter,
gas meter or water meter (e.g.: 800 meters / kWh on the meter).
• Type – selection of measured quantity (electricity, cold water, hot water,
gas)
RFTM setup - RFTM-1 input
• + – Add RFTM-1 converter
• Name – RFTM-1 name optionally chosen
• Unit – Unit of measurement (kW / h - for electricity measurement or m
for water or gas measurement)
• Type – selection of measured quantity (electricity, cold water, hot water,
gas)
• Pulses – Pulse value for the measured value (the value that translates the
number of pulses per unit of a given quantity) - this is given on the meter,
gas meter or water meter (e.g.: 800 meters / kWh on the meter).
• Interval – After the set time interval has elapsed, RFTM-1 sends information about the magnitude of the measured value (minimum interval is 1 minute).
• Treshold – the pulse value pulse interval - after recording the set number of pulses RFTM-1 sends information on the size of the measured value (the minimum number of pulses is 1) - the RFTM-1 can
send this information at most once per minute
• Address – The RF address that is listed on RFTM-1
• Trash symbol – RFTM-1 removal (after removing RFTM-1 and replacing it with another RFPM-1, the measured values of the original RFPM-1 remain stored in the graph, these values are then displayed as
a one-off curve of the last value).
• If the saved changes are not refl ected in the browser, you must refresh it.
Made in Czech Republic
The entire RFPM2-M is divided into several parts:
- Set up a network interface that allows network communication.
- setting of RFTM-1 pulse transducers
- External RFPM-2 inputs and security settings.
- price settings
- settings for each phase
- password and currency settings
3 -
3
-
ELKO EP, s.r.o. | Palackého 493 | 769 01 Holešov, Všetuly | Czech republic | e-mail: elko@elkoep.com
Support: +420 778 427 366
EN
www.elkoep.com
02-5/2018 Rev.1
4/7