Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Instruction Manual
for pendant fitting
NEW PARA DOME
Please read carefully and keep for further reference !
1.
Use as directed:
This product serves exclusively lighting purposes and may:
only be used with a voltage of 230V ~50Hz.
only be used in dry condition,
not in damp or dirt-endangered rooms.
not in areas of high air humidity.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2.
Technical Data:
Operating voltage:
230V ~50Hz
Ignition voltage:
kV
Safety class:
I
Bulb:
HIE, E40
165140: 250W / 165150: 400W
Dimensions (Ø/H):
48 / 56cm
Weight:
165140: 6,85kg / 165150: 7,10kg
Importeur:
SLV Elektronik GmbH
3.
Installation
The electric connection may be executed only by an electric expert
who is familiar with the valid directives!
Attention: Switch off the power of the mains supply line or
respectively of the connection lead before doing any works
parts, which are supplied with the product or are described as accessories!
Otherwise the product or the installation might not be sufficiently safe.
Installation place:
The product is suited for ceiling installation.
Make sure that the product is mounted on a stable, even and tilt-fixed
background.
The light exit should be placed at least so far from the illuminated surface,
as indicated as minimum distance on the type plate of the luminaire:
250W:
/ 400W:
. Pay special caution to easily
inflammable objects (e.g. curtains).
Separate Installation Steps
Install the suspension for the fitting. Use a chain (not supplied). Pay
attention that the suspension supports the weight of the fitting.
Prepare the power supply lead (not supplied).
Take the chassis plate out of the housing.
Attach the cable screwing on the housing of the light unit (1).
Attach the chains from the housing on the chassis plate (2).
Establish the earth connection from the chassis plate to the housing (3).
Fasten the housing on the prepared suspension (4).
Direct the power supply lead in sufficient length through the cable
screwing. Secure the cable screwing (5).
Electrical Connection
The product must be able to be separated by an all pole separation
from the current supply.
Equip the three wire ends with protective tubes.
For electric connection attach the black or brown wire (live conductor)
of the mains supply with the clamp L and the blue wire (neutral
conductor) of the mains supply with the clamp N. The green-yellow
250W/ 400W
wire (protective conductor) of the mains supply has to be tightly
screwed into the earth clamp
Fasten the chassis plate back into the housing (6).
Fasten the socket on the chassis plate (7).
Inserting the bulb: Use a piece of fabric to insert the bulbs. Do not
touch them with bare fingers. Screw the bulb into the socket (8).
Attach the reflector on the housing securely.
Ensure that the light fitting and all components are kept securely!
The product is now ready for operation.
4.
Operation
It takes about five minutes until the lamp reaches its full potential.
After switching it off, wait 5 to 10 minutes to let the bulb cool down
before restarting it.
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention: Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no decoration.
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
What is to do if a bulb is defect or does not work?
.
Use only
Disconnect the product from power, before you exchange the bulbs.
Caution: Let the bulb cool down first before replacement – otherwise
considerable risk of injury exists because of the hot surface.
Replace the bulbs only with bulbs of the same data like socket, power
and capacity. Every other sort of bulb can lead to damages of the light.
Replacing the bulb: see Installation.
5.
What else has to be considered?
Disconnect the product from power, before you...
clean or maintain the product.
do any works on the product or its components (electric expert).
of the product.
:
nicht im Lieferumfang
not supplied
exclue à la livraison
5
no incluida en el
volumen de suministro
wordt niet meegeleverd
4
3
2
6
2
!
7
8
9
06/2007 © by SLV Elektronik GmbH
165140/50
Technical Details are subject to change.
Duplication prohibited !
1
2
L
N
Publicidad
