Play Modes; Daisy Chain Playback - Denon DCM-5001 Instrucciones De Operación

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Play modes

2 Zone modes
The DCM-5001 has two sets of outputs (zone 1 and zone 2), and different playback signals can be output from each zone when in
the multi zone mode.
Select the zone mode before starting playback.
SINGLE:
The same signals are output from zone 1 and zone 2.
MULTI:
Separate playback signals are output from zone 1 and zone 2.
2 Continuous and random modes
Continuous mode: All tracks of all discs are played in order starting from the lowest disc number.
In the multi-zone mode, disc 1 in zone 1 and disc 2 in zone 2 are played first, after which the next
appropriate discs are selected and played in order.
Random mode:
All the CDs are played in random order. One track is selected at random from each of the CDs.
2 Cross fade playback
The cross fade play function can only be used in the single zone mode.
The cross fade mode allows you to play tracks continuously without breaks in the sound by fading in and out when switching from
playback on one disc to a track on the next disc.
Cross fade playback is possible, as described on the table below.
Random mode:
NOTE:
• No signals are output from the digital outputs when the cross fade mode is selected.
In all play modes, playback starts over from the beginning of the first disc once the last disc is played. (The repeat play mode is set.)
*
Playback
• Once connection to the amplifier, disc setting and setting of the play mode with the mode switches are completed, once press the
POWER OPERATION switch to turn off, and press the POWER OPERATION switch again to turn on.
ON / STANDBY
Off
OFF
Playback begins in the set mode.
Turn off the POWER OPERATION switch to stop playback.
*
When the DCM-5001 is used in the stand-alone mode, there is no standby mode for the POWER OPERATION switch. The power can
¢
only be set to ON (
) or OFF (
7

DAISY CHAIN PLAYBACK

Connections (outline)
Audio signal
To amplifier
Main unit
(DCM-5000)
Digital output
Audio (digital audio) signal (COAXIAL)
To connect in daisy chain, connect as shown on the diagram above. For details, refer to the following page.
• Daisy chain control signals: Connect the connector cords (5-pin cords, included) from the last sub unit in the chain to the next
• Digital audio signals:
* Digital output from the main unit (DCM-5000) with the daisy chain.
Each unit in the daisy chain has its own digital output signals based on the each system clock and the main unit transfers its digital
data to outside equipments.
So it may cause the digital-unlock for a while and may result a pause in the sound or a spike noise when switching to another unit
during the daisy chain operation. It depends on the receiving equipments (digital amp, D/A converter etc.) respectively.
In this case, do not connect the digital output to other equipments.
(We recommed to use the Audio signal output)
Cross fade playback is performed between tracks on discs selected at random (one track per disc).
Order of playback: Disc 3, Tr 5 e Disc 18, Tr 1 e Disc 56 Tr 3 e Disc 29, Tr 4 e ...
The indicator lights (green) if there is no disc. Load a disc.
£
).
Daisy chain control signal (5P MINI-DIN)
1st sub unit
(DCM-5001)
higher one, and so on.
These are connected in the same way as the daisy chain control signals. Be sure to connect both
connector cords (included) between the units, whether you select the single zone mode or the multi
zone mode.
2nd sub unit
(DCM-5001)
ENGLISH
11

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido