Transmitter Set-Up (Australia And New Zealand) - Petsafe HIG11-13655 Manual De Adiestramiento Y Funcionamiento

plate center screw. Plug the Surge Protector into the
lower outlet and then secure the cover plate using the
longer screw included with the protector. The screw is
for mechanical attachment only and does not ground the
protector. Remove the tape and turn ON the power to the
outlet.
3. Run the Boundary Wire through a window, under a door,
through a crawl space vent, or any other appropriate
available access. You can also drill a hole through your wall.
4. Strip
Wire. Insert the stripped ends into the 2 left red connector
holes on the bottom of the Surge Protector labeled
"Loop" (4B). There should be 1 wire in each connector
hole. Press the plastic tab, insert the wires and release the
tab. Make sure the wires do not touch each other at the terminals.
5. Determine the length of wire needed to pass from the Surge Protector to the Fence
Transmitter. Measure and cut 2 lengths of wire, then strip
ends. Twist the 2 lengths together, with at least 10-12 twists per foot, so the wires will
not send out a signal.
6. Insert the ends of the twisted transmitter wires into the right 2 black connectors at the
bottom of the Surge Protector labeled "Transmitter".
7. Press the red plastic tabs on the Fence Transmitter and insert the opposite ends of the
twisted wire into the Boundary Wire Terminals.
8. Turn the Boundary Width Control knob to 10. This will set the Boundary Width at the
maximum width.
9. Plug in the transmitter power adapter to the outlet on the front of the Surge Protector.
10. The Power Light and Loop Indicator Lights should come on. If this does not happen, see
the "Troubleshooting" section.
Transmitter Set-up
1. Run the Boundary Wire through a window, under a door, through a crawl space vent, or
any other appropriate available access. you can also drill a hole through your wall.
2. Strip
3
3. Press the red tabs on the Fence Transmitter and insert the twisted wire into the
Boundary Wire Terminals. Make sure wires do not touch each other at the terminals.
4. Turn the Boundary Width Control Knob to 10. This will set the Boundary Width at the
maximum width.
5. Plug Power Adapter into Power Jack and AC Power Outlet.
6. The Power Light and Loop Indicator Lights should come on. If this does not happen see
the "Troubleshooting" section.
14
⁄ inch of insulation from the ends of the Boundary
3
8
Verify that the boundary loop and transmitter wires connect to the proper
Surge Protector terminals. Reversed connections will result in an increased
risk of surge related damage.
For added protection, when unused for long periods of time or prior to
thunderstorms, unplug from the wall outlet and disconnect the loop boundary
wires. This will prevent damage to the transmitter due to surges.
⁄ inch of insulation from the ends of the Boundary Wire.
8
• Do not install, connect, or remove your system during a lightning storm. If the
storm is close enough for you to hear thunder, it is close enough to create
hazardous surges.
• Risk of electric shock. Use the Fence Transmitter indoors in dry location only.
If possible, DO NOT use an AC circuit protected with a Ground Fault Circuit
Interrupter (GFCI) or Residual Current Device (RCD). In rare cases, nearby
lightning strikes may cause the GFCI or RCD to trip. Without power your dog
may be vulnerable to escape. You will have to reset the GFCI or RCD to restore
power to the system.
For added protection, when unused for long periods of time or prior to
thunderstorms, unplug from the wall outlet and disconnect the loop boundary
wires. This will prevent damage to the transmitter due to surges.
(Australia and New Zealand)
1-800-732-2677
4B
⁄ inch of insulation at both
3
8