Fm Approved Slcab Connection / Termination Kit; Fm Approved Slmcab Connection / Termination Kit; Csa Approved Slcab And Slmcab Connection / Termination Kit - BriskHeat SLCBL Serie Manual De Instrucciones De Instalación Y Mantenimiento

FM APPROVED SLCAB connection / termination kit

KITS
SLCABUC: SLCAB Universal Connection Kit. FM approved.
1 3/4" (19mm) NPT pipe standoff
2 Ring terminals
4 Large, Insulated crimp connectors
2 Small, Insulated crimp connectors
2 Pipe straps (for up to 6" (152mm) IPS pipe)
2 Heat sink end caps
1 6" (152mm) shrink sleeve
1 3 oz. (89ml) tube of RTV sealant
1 Roll of fiberglass tape
1 Caution label
1 Ground screw
SLCABSK: SLCABSK Kit. FM approved.
20 Large yellow crimp connectors
20 Large blue crimp connectors
10 Heat shrink tubes
1 3 oz, (89ml) tube of RTV sealant
SLCABKC: SLCAB End Seal Kit. FM approved.
10 Heat shrink tube

FM APPROVED SLMCAB connection / termination kit

KITS
SLMCABUC: SLMCAB Universal Connection Kit. FM approved.
1 3/4" (19mm) NPT pipe standoff
2 Ring terminals
3 Large, crimp connectors
2 Small, crimp connectors
2 Pipe straps (for up to 6" (152mm) IPS pipe)
2 End boots
1 3 oz. (89ml) tube of RTV sealant
1 Roll of fiberglass tape
1 Caution label
1 Ground screw
SLMCABKC: SLMCAB End Seal Kit. FM approved.
10 End boots
4 Roll of fiberglass tape
1 3 oz, (89ml( tube of RTV sealant))
®
© BriskHeat
Self Regulating Heating Cable
USAGE
Ordinary Locations
Hazardous (Classified) Locations
Class I, Division 2, Group B, C, D
Class II, Division 2, Group F, G
Class III, Division 2
Approvals valid only when used with appropriate heating cable and installation
accessories, and installed in accordance with all applicable instructions, codes, and
regulations.
Enough to complete:
Two end terminations and one input connection, or one input power splice
NOTE: Requires a 3/4" (19mm) NPT junction box
Enough to complete:
Ten input power connections, or Ten tee splices
Enough to complete:
Ten end terminations
USAGE
Ordinary Locations
Hazardous (Classified Locations
Class I, Division 2, Group B, C, D
Class II, Division 2, Group F, G
Class III, Division 2
Approvals valid only when used wir appropriate heating cable and installation
accessories, and installed in accordance with all applicable instructions, codes, and
regulations.
Enough to complete:
Two end terminations and one input connection, or one input power splice, or one tee
splice
NOTE: Requries a 3/4" (19mm) NPT junctiuon box
Enough to complete:
Ten end terminations
Corporation. All rights reserved.
15

CSA APPROVED SLCAB AND SLMCAB connection / termination kit

KITS
SLCABUC-CSA-M: SLCAB and SLMCAB Universal Connection Kit. CSA approved.
1 Connector body
1 Connector cap
2 Connector gland washers
1 Grommet
1 Termination boot
1 Stain relief grip
1 Standoff bracket
1 Locknut
1 Termination block
1 Roll of fiberglass tape
1 Silicone sealant
1 Pipe strap (for 2" to 6" (51 to 152mm) O.D.pipes)
1 Ring tongue terminal
1 End seal kit
SLCABEND-CSA-2: SLCAB and SLMCAB End Seal Kit. CSA approved.
1 End cap
1 Clamp
1 Sealant
CSA APPROVED SLHCAB connection / termination kit
KITS
SLCABPWP-H : SLHCAB Power Connection Kit for pipes. CSA approved.
1 Base
1 Top
2 Junction Box
1 Sealing Grommet (large hole)
1 Sealing Grommet (small hole)
1 Sealing Gasket
2 Shrink Tubes 1/8" x 51/2" (black)
1 Shrink Tube 1/4" x 51/2" (green/yellow)
1 Shrink Tube 1/2" x 11/2" (white)
1 Lock Ring
1 Adaptor (for installation on pipe smaller than 1")
1 Stainless Steel Tie Wire
SLCABKC-H: SLHAB End Seal Kit. CSA approved.
1 End cap
1 Clamp
1 Sealant
†
CI/D1 approval for BF only. Contact a BriskHeat representative for information on Division I hazardous location systems.
®
© BriskHeat
Self Regulating Heating Cable
USAGE
Ordinary Locations 130-03 (-G,-W, -S)
Hazardous (Classified) Locations
†
Class I, Division 1 and 2, Groups B, C, D
†
Class II, Division 1 and 2, Groups E, F, G
†
Class III, Division 1 and 2
3, 5, 8 W/ft T6
10 W/ft T5
Approvals valid only when used with appropriate heating cable and installation
accessories, and installed in accordance with all applicable instructions, codes, and
regulations.
*2E approved for 3 watts/ft and 5 watts/ft only
Enough to complete:
One input connection and one end termination. Splices and power input splices can be
made using two kits
NOTE: Requires a 3/4" (19mm) NPT junction box
Enough to complete:
One end termination
USAGE
Ordinary Locations 130-03 (-G,-W, -S)
Hazardous (Classified) Locations
Class I, Division 1 † and 2, Groups B, C, D
†
Class II, Division 1 and 2, Groups E, F, G
†
Class III, Division 1 and 2
3, 5, 8 W/ft T6
10 W/ft T5
Approvals valid only when used with appropriate heating cable and installation
accessories, and installed in accordance with all applicable instructions, codes, and
regulations.
Enough to complete:
One input connection and one end termination. Splices and power input splices can be
made using two kits
NOTE: Requires a 3/4" (19mm) NPT junction box
Enough to complete:
One end termination
Corporation. All rights reserved.
16