Genius LYNX 06 Instrucciones Para El Uso página 18

Page 14 LYNX 06
Guide for the installer
1. DESCRIPTION
Thank you for choosing our product. GENIUS is sure you will get the
performances you expect to satisfy your requirements. All our products
are the result of a many years' experience in the field of the automated
systems, strengthened by being part of a world leading group in this
sector.
The LYNX 06control units are designed and built for managing electro
– mechanical barriers for controlling residential accesses.
The two models differ in their voltage:
• Lynx 06: Power supply 230V
• Lynx 06: Power supply 115V
Thanks to their wide ranging number of selectable parameters, these
control units can be adapted to your requirements guaranteeing optimal
operation of the automated system.
The possibility of managing an encoder for detecting any obstacles enables
you to further increase the safety level of the automated system.
Programming the main operating parameters is done by pressing two
keys on the control unit and is shown on the generous back lit display.
During normal operation, the display shows the status of the automated
system at all times. Learning the work cycle and the mechanical stop-
points is performed automatically while the first cycle is being performed
(whenever power is cut, the control unit searches the stop-points both
at opening and closing).
The six integrated LEDs constantly indicate the inputs status.
2. TECHNICAL SPECIFICATIONS
Supply voltage of control unit
Absorbed power
Motor absorbed power
Accessories max. load
Power supply and indicator light
max. load
Power supply and max load of bar-
rier status indicator light
Operating ambient temperature
Protective fuses
Function logics
Opening / closing time
Pause time
Motor power
Slow-down time
Obstacle detection
Selectable functions
Terminal board inputs
Inputs with connector
Terminal board outputs
Board dimensions
a According to board model, 230 V~ or 115 V~.
230/115 V~ 50/60 Hz a
3 W
500 W
500 mA
230 V~ 25 W
24 V 5 W
-20°C +55°C
F1= T5A (Transformer and motor
primary winding)
F2= T500mA (accessories and in-
dicator light)
Automatic / Step-by-step automat-
ic /Semiautomatic /Step-by-step
semiautomatic / Condo
In self learning mode during first
manoeuvre
Nine levels selectable up to a max-
imum of 4 minutes
Adjustable on several levels
Three selectable levels
With optional encoder
Operates with or without encoder
/ Encoder sensitivity/Automatic
closure / Open input operation/
Condo function / Slow-down
percentage/ Heating function /
Immediate closure / Timer function
/ Soft start / Photocells operation /
Maintenance request
Opening / Closure / Photocells /
Opening travel limit device /Closure
travel limit device / Stop / Mains
power supply / Earthing
Radio module / thrust capacitor /
encoder
Power supply to accessories /
Flashing lamp / Motor /
Indicator light
147 x 112 mm
3. PREPARATORY ACTIONS
To ensure people's safety, all warnings and instructions in this
booklet must be carefully observed. Incorrect installation or
incorrect use of the product could cause serious harm to
people.
Keep the instructions for future reference.
• Make sure that an adequate differential switch is installed upstream of
the system as specified by current safety regulations.
• On the main power supply, install a thermal breaker with omnipolar
switching.
• Make sure that an adequate earthing system is available.
• To lay cables, use adequate rigid and/or flexible tubes.
• Always separate the 230/115 V~ power cables from low voltage
connections, using separate sheaths to avoid possible interference.
4. BOARD LAYOUT (Fig. 1)
CN1 Power supply terminal-board
CN2 Encoder connector
CN3 Travel limit terminal-board
CN4 Terminal board for commands / powering accessories
CN5 Capacitor connector
JP1 Connector for radio module
DSP1 Display
F1 Fuse for transformer primary winding/Motor power supply
F2 Fuse for accessories/indicator light
P1 Parameters adjustment push-button
P2 Parameters adjustment push-button
P3 OPEN/CLOSE radio channel memory storage push-button
P4 CLOSE radio channel memory storage push-button
P5 RESET push-button
FCA FCA input LED
FCC FCC input LED
CLO-
CLOSE input LED
SE
OP/CL OPEN/CLOSE input LED
FSW FSW input LED
STOP STOP input LED
DL7 OPEN/CLOSE radio channel LED
DL8 CLOSE radio channel LED
5. CONNECTION AND OPERATION
5.1. CN1 TERMINAL-BOARD (Fig. 2)
5.1.1. e
arthing
Terminal "1". Connect the yellow-green power cable to this terminal.
The connection is absolutely necessary for correct operation
of the control unit.
5.1.2. p
ower supply
Terminals "2 & 3". Connect, to these terminals, the two cables incoming
from the 230/115 V~ power supply line according to board model.
Connect the neutral wire to terminal 3 and the phase to terminal 2.
5.1.3. F
lashing laMp
Terminals "4 & 5". Output 230/115 V~ max. 25 W. The flashing lamp power
cable must be connected to these terminals. The flashing lamp is active
while the automated system is moving, whereas when the system is open
or closed, it stays OFF. Before the opening manoeuvre, the flashing lamp
pre-flashes on steady beam for 0.5 sec. If the assistance request function
has been activated, an when the set number of cycles has been reached,
at the end of the closing manoeuvre, the flashing lamp continues to flash
for another 5 seconds, indicating that the set cycles have been reached.
For the cycles resetting operation, see paragraph 10.1.