Memory Storing The Radio Code; Control Leds - Genius LYNX 06 Instrucciones Para El Uso

Page 16 LYNX 06
Guide for the installer
5.5. CONNECTOR CN5
This connector is used for connecting the thrust capacitor.
If you have a connector without a terminal for insertion on this
connector, the capacitor can be connected in parallel to the two
motor phases: terminals 6 & 8.
6. INSERTION OF A RECEIVER MODULE (Fig. 5)
The control unit is designed to house an 868 or 433 MHz receiver module.
The receiver module must be fitted on the JP1 connector, respecting the
orientation defined by the housing - see figure.
Fitting and, if necessary, removing the receiver module must
be done only after cutting power to the control unit.

7. MEMORY STORING THE RADIO CODE

The control unit has an integrated 2-channel decoding system. The
system makes it possible to memory store - via the receiver module - both
the OPEN/CLOSE command and the CLOSE command.
The decoding system makes it possible to memory store both the radio
controls with a frequency of 868 MHz and the radio controls with a
frequency of 433 MHz.
Only one radio code can be used at a time. To change over
from one code to the other, delete the existing radio code
(see paragraph 7.3), replace the receiver module and repeat
the programming stages.
Fitting and, if necessary, removing the receiver module must
be done only after cutting power to the board.
The receiver module can only be inserted in one position. Orient
the module correctly without forcing.
7.1. MEMORY STORAGE OF 868 MHz RADIO
CONTROLS
Before you save the radio control, we advise you to run a deletion
procedure – see paragraph 7.3.
You can memory store up to a maximum of 250 codes, subdivided
between the two channels, OPEN/CLOSE and CLOSE.
1. On the radio control, simultaneously press and hold down push-
buttons P1 and P2 (see radio control instructions).
2. After about one second, the LED of the radio control begins to
flash.
3. Release both push-buttons.
4. Press and hold down push-button P3 or P4 on the board, according
to the input you wish to save (input of OPEN/CLOSE or CLOSE).
When the relevant LED begins to flash - release the push-button.
5. Simultaneously press the push-button of the radio control with which
you wish to associate the selected command.
6. Check if the LED relating to the command being memory stored
(DL7 for the OPEN/CLOSE channel or DL8 for the CLOSE channel)
lights up on steady beam for about two seconds to confirm correct
memory storage.
7. To finish programming, press twice in close succession, the push-
button of the memory stored radio control.
The automated system will perform an opening manoeuvre
- make sure that there are no obstacles inside the operating
range.
8. To memory store the other channel, repeat all the procedure from
point 1.
To add other radio controls, transfer the code of the memory-stored push-
button of the radio control to the relevant push-button of the radio controls
to be added, repeating the memory storage procedure or observing the
following procedure:
• On the memory stored radio control, simultaneously press and hold
down push-buttons P1 and P2 (see radio control instructions).
• The radio control LED begins to flash.
• Release both push-buttons.
• Put the two radio controls frontally into contact.
• On the memory stored radio control, press and hold down the push-
button relating to the channel you wish to transfer - the radio control
LED lights up on steady beam.
• On the radio control to be memory stored, press the required push-button
and release it after the radio control has flashed twice.
• To finish programming, press twice in close succession, the push-button
of the memory stored radio control.
The automated system will perform an opening manoeuvre
- make sure that there are no obstacles inside the operating
range.
7.2. MEMORY STORAGE OF 433 MHz RADIO
CONTROLS
Before you save the radio control, we advise you to run a deletion
procedure – see paragraph 7.3.
You can memory store up to a maximum of 250 codes, subdivided
between the two channels, OPEN/CLOSE and CLOSE.
1. On the control unit, press the push-button of the channel you wish
to memory store, P3 for the OPEN/CLOSE channel or P4 for the
CLOSE channel.
2. The relevant LED on the control unit begins to flash - release the
push-button.
3. On the radio control, press the push-button with which you wish to
associate the selected channel.
4. The LED on the control unit lights up on steady beam for about one
second, signalling that the radio control was stored in the memory,
then it resumes flashing.
5. During this stage further radio controls can be stored in the
memory.
6. After about 10 seconds, the control unit automatically exits the
learning stage.
7. To add other radio controls or memory store the second channel,
repeat the operations from point 1
7.2.1. r
eMote MeMory storage oF
Other radio controls can be remotely stored only with the 433 radio
controls, i.e. without using the push-buttons of the control unit, but using
a previously stored radio control.
1. Get a radio control already memory stored on one of the 2
channels.
2. Step near to the automated system.
3. Press and hold down push-buttons P1 and P2 (see radio control
instructions) simultaneously for about 5 seconds.
4. Within 5 seconds, press, on the memory stored radio control , the
push-button you wish to transfer to the new radio control. In this
way the learning stage on the selected channel is activated on the
control unit.
5. Within 5 seconds, press, on the new radio control, the push-button
you wish to associate with the selected channel.
6. After the new radio control has been stored in the memory, the
control unit keeps the learning mode active on the selected channel
for about 5 seconds.
7. During these 5 seconds, other radio controls can be memory stored
on the control unit, as ever associated with the activated channel.
8. When 5 seconds have elapsed from memory-storage of the last radio
control, the control unit automatically exits the learning stage.
9. To check if the radio control was correctly memory stored, wait for
5 seconds after sending the code.
7.3. DELETION OF RADIO CODES
To delete all the radio controls stored in the memory, go through the
following procedure:
1. Press and hold down one of the two push-buttons P3 or P4.
2. The relevant LED begins to flash.
3. After five seconds, the LED starts to flash at high speed.
4. After another five seconds both LEDS, DL7 and DL8 light up on
steady beam.
5. Release the push-button.
This operation is irreversible, and all radio controls associated
with both the OPEN/CLOSE and the CLOSE command will be
deleted.
8. CONTROL LEDS
There are 8 control LEDs on the control unit, displaying the state of the
inputs. The meanings of the LEDs are shown on the table below
LEDS
FCA - Opening travel Opening travel limit
limit device FCA device not engaged
FCC - Closure travel lim- Closure travel limit de-
it device FCC vice not engaged
CLOSE - CLOSE in-
Input active
put
433 Mh
z radio controls
ON OFF
Opening travel limit de-
vice engaged
Closure travel limit
device engaged
Input not active