Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Do not force tool. It will work most efficiently at the
rate for which it was designed.
Keep hands away from moving parts and cutting
surfaces.
Never leave tool running unattended.Turn
the power
off and do not leave tool until it comes to a complete
stop.
Do not overreach. Keep proper
footing and balance.
Never stand on tool. Serious injury could occur if tool
is tipped or if blade is unintentionally
contacted.
Know your tool. Learn the tool's operation,
applica-
tion and specific limitations.
Use recommended
accessories. Use of improper
accessories may cause risk of injury to persons.
Handle workpiece correctly. Protect hands from pos-
sible injury.
Turn machine off if it jams. Blade jams when it digs
too deeply into workpiece. (Motor force keeps it
stuck in the work.) Do not remove jammed or cut off
pieces until the saw is turned off, unplugged
and the
blade has stopped.
Maintain proper adjustment
of blade tension, blade
guides and thrust bearings.
Adjust upper guide to just clear workpiece.
Hold workpiece firmly against table.
DIRECTION OF FEED:Feed work into a blade or
cutter against the direction of rotation of the blade or
cutter only.
WARNING:
The operation of any power tool can result
in foreign objects being thrown into the eyes, which can
result in severe eye damage. Always wear safety goggles
complying with United States ANSI Z87.1 (shown on
package) before commencing
power tool operation.
Safety goggles are available at SearsStores or Craftsman Outlets
Check for shipping damage and missing parts. If item is
damaged or parts missing, call 1-800-469-4663.
Model 124.214000 10" band saw is shipped complete
in one box.The band saw comes assembled as one
unit. Additional
parts which need to be fastened to the
saw should be located and accounted for before
assembling (see Figure 1).
A Main Machine (1)
B Fence Assembly (1)
C Table (1)
D Guide Rail (1)
E Owner's Manual (1)
F UpperTableTrunnion
Assembly (1)
G Bag of Loose Parts (1)
Parts bag includes: Blade Tension Knob (1), Miter Gauge
(1), Hex Socket Head Cap Screw M6x30 (1), Washer
M6 (1), Wing Nut M6 (1), Hex Bolt M6xl 2 (4), Lock
Washer M6 (4), Star Knob Screw (2), Washer M6 (2),
M3 Hex "L_'Wrench (1), M5 Hex "L_'Wrench (1).
A
D
E
Figure 1 - Unpacking Band Saw
G
IMPORTANT:
Table is coated with a protectant.To
ensure proper fit and operation, remove coating.
Coating is easily removed with mild solvents, such as
mineral spirits, and a soft cloth. Avoid getting solution
on paint or any of the rubber or plastic parts. Solvents
may deteriorate
these finishes. Use soap and water on
paint, plastic or rubber components. After cleaning,
cover all exposed metal surfaces with a light coating of
oil. Paste wax is recommended
for table top.
WARNING:
Never use highly volatile solvents. Non
flammable solvents are recommended
to avoid possible
fire hazard.
CAUTION:
Do not attempt assembly if parts are miss-
ing. Use this manual to order replacement
parts.
The machine is supplied partly assembled. Prior to use,
the following
items have to be installed:Table, blade
tension knob and rip fence.
WARNING:
To avoid injury, do not attempt to run or
use this machine until all parts are assembled and
working properly.
ASSEMBLE TABLE TRUN NION
Assemble the upper table trunnion to the lower table
trunnion with carriage bolt, glide piece, washer and
wing nut. Place the table on to the upper table trun-
nion, taking care when passing the saw blade
through the slot of the table (see Figure 2).
Figure 2 - AssembleTrunnion
Table
Publicidad
Tabla de contenido
