Preliminary Operations; Water Connection; Assembly Of Accessories - Jacuzzi folia Manual De Instalación

PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE
INSTALLING
Important
Please ensure that you thoroughly check the product upon receipt
since we cannot accept responsibility for any damage reported af-
ter installation. Should you find any damage, please immediate-
ly notify the forwarder.
WE RECOMMEND CHECKING THAT ALL THE ARRANGE-
MENTS COMPLY WITH THE INSTRUCTIONS FOR PRE-
INSTALLATION.
I Unpack the bath and lift it only by the rim and never by any pipe
line or electric equipment (use protective gloves).
I Check for any damage or defects by removing the pro-
tective plastic film (damages from impact or scratches re-
ported after installation are not covered by our guarantee).
I Check that the clamps holding the rubber couplings
and the air lines are tightly fastened.
I The installation of the whirlpool baths can be made against fin-
ished (tiled) walls and floor.
The panels allow access to electromechanical devices in-
stalled under the bath rim, as well as proper aeration re-
quired for water-air mixture during hydromassage.
Aeration must be guaranteed also if Jacuzzi
not used (see "Instruction for pre-installation"). Panels
must be firmly installed and proper tools must be used
when being removed. Openings, holes, grids, used for
aeration, should not allow the introduction of objects
having a diameter of 12 mm or larger.

PRELIMINARY OPERATIONS

i
I (
1
) Place the tub in its location of installation. Level it and
adjust the height by manually turning the feet (A) located on
i
the corners of the tub (
NOTE: The upper level of the tub, measured at the end of the
edge, must be at a height of 60 cm from the floor. To com-
pensate for possible irregularities of the floor, the bath feet
can be regulated from -0,5 + 1 cm
DO NOT TOUCH BLOCKING NUTS (G) MARKED WITH A
RED ARROW STICKER (
i
I (
2 ) Mark on the floor a hole for each outer foot. One hole
is enough.
Remove the bath and drill the floor.
Insert screw anchors (B). Adjust center feet (A1) so they rest
i
1
firmly on the floor (
If the tub calls for installation of Jacuzzi
the edge of the bath, install them (
is positioned and secured in its location of installation.
® panels are
1
).
i
2 ).
).
® tap fixtures on
i
5
) before the tub
i
I (
3 or 4, depending on the model
ble the drain column and connect it with a siphon, preferably a
plastic one.
If filling of the tub takes place via the column (dis-
pensed form overflow) you will need to install a specif-
ic DB-type protection unit (standard EN 1717), located
at least 15 cm above the edge of the tub. Concerning
system methods, we recommend you contact your wa-
ter company and/or your plumber.
I Before fixing the bath to the floor, a final test for possible wa-
ter leaks caused by transport damage should be made. Fill the
bath up to approx. 5-6 cm. above the uppermost hydromas-
sage jets.
Please make sure that all joints and fittings are thoroughly in-
spected, before emptying the tub.
i
I (
2
) Drain the bath and secure all outer feet with screws
(C) to the floor.
i
1
( ) Adjust center feet (A1) so they rest firmly on the floor.
(Refer also to the "Electric safety" chapter in the WIRING DIAGRAM
manual)
I
Connect the electric box and the power line respecting the
symbols "L" - phase, "N" -neutral and
the lid from the box, establish the connections, and close
the lid carefully. Secure the cable clamp well to ensure pro-
tection from jets of water.
IMPORTANT: for Countries where 220-240V voltage
is supplied by a two-phase system (L+L), the connec-
tion has to be made on terminals L and N anyway.
ASSEMBLING THE TAPS AND FITTINGS
(if included)
In the accessory kit box, which contains the various taps and
fittings, you will find the instructions for assembling them.

WATER CONNECTION

Filler/overflow assembly
i
I (
5
) The connection must be made of the mixed water pipe
(see pre-installation diagram) to the outlet of the drain column.
The column has two 1/2" diameter inputs, of which one is
plugged. If necessary the plug (D) may be moved from one in-
put to the other, depending on the type of installation
Note: if a metal drain column is used (other than the one
provided) it must be connected to the equipotential contact
(see chapter on ELECTRIC SAFETY).

ASSEMBLY OF ACCESSORIES

i
I
( 6
) Secure the suction cover, supplied with an O-ring, by
tightening the screw
i
I
( 7
) In models with hydromassage, you may install as you
wish the rotating jets (Twist Jet) or the directional ones (Hy-
dro Jet) as shown:
5
) At this stage, assem-
- ground: remove