Briteq BT-METEOR Manual De Instrucciones página 10

ENGLISH
PAN inversion
TILT inversion
Display on/off
FOCUS Adjust
Function Delay
FanSpeed
Dimmer curve
Loading PRO or AUTO defaults:
 Use the ▼/▲ buttons to select either [AUTO def] or [PRO def] and press [ENTER] to confirm.
 Display shows [Load]: press [ENTER] to confirm (or [MODE] to return).
 To avoid that current settings are overwritten by accident the display shows by default [NO].
 Use the ▼/▲ buttons to select [YES] and confirm with [ENTER].
 The default settings are now loaded.
If you want to go back to normal running mode: press the [MODE] button for about 2 seconds.
Loading, saving and editing USER-defaults:
 EDITING: Starting from the PRO and AUTO defaults you can easily make your own [USER] settings: just
make your changes in the setup menu (refer to the table to see which settings are saved).
 SAVING: Once the settings are OK, just save them to the personal [USER]defaults:
 Use the ▼/▲ buttons to select [USER def] and press [ENTER] to confirm.
 Display shows [Load]: use the ▼/▲ buttons to select [Save] and press [ENTER] to confirm.
 To avoid that current settings are overwritten by accident the display shows by default [NO].
 Use the ▼/▲ buttons to select [YES] and confirm with [ENTER].
 Your new settings are now saved to [USER def] (user defaults memory).
If you want to go back to normal running mode: press the [MODE] button for about 2 seconds.
 LOADING: same actions as for saving the settings but now you choose the [Load] option (loading).
Reset
Used to force a full or partial reset of the unit.
 Press the [MODE] button and use the ▼/▲ buttons until the display shows [Reset].
 Press the [ENTER] button: the display shows [All] (reset all functions)
 Press the [ENTER] button again to reset the unit.
OR
 Use the ▼/▲ buttons to select the function that you want to reset. You can do a partial reset of the
following functions: [Pan & Tilt], [Color], [Gobos], [Prism] and [Focus].
 Press [ENTER] to reset the selected function: the display shows [Reset ...] as long as the reset takes.
If you want to go back to normal running mode: press the [MODE] button for about 2 seconds.
Note: you can also perform a full reset by DMX. Choose DMX-value 200-209 on the "Special functions"
channel (channel 11 or 14), see the DMX-chart for more information.
Firmware version
Used to show the software version that is installed in the unit
 Press the [MODE] button and use the ▼/▲ buttons until the display shows [Firmware].
 Press the [ENTER] button to show the software version on the display.
 To go back to the functions press the [MODE] button.
OFFSET MENU:
This is a hidden menu where you can fine-tune the offset of several functions. To access this menu do as
follows: press the [ENTER] button for about 3seconds while you are in the SETUP menu (any option, not
important). Now the OFFSET menu (calibration menu) shows up:
 Use the ▼/▲ buttons to browse the menu.
 Select a function with the [ENTER] button.
 Use the ▼/▲ buttons to change the values.
 Press the [ENTER] button to select.
 Press the [MODE] button for about 2 seconds to store the setting and to return to running mode. If you
don't do this, the setting will not be stored and after some time, the fixture will return to the previous
running mode.
BRITEQ
®
No No
No No
OFF on
Value 127 Value 140
3 sec 3 sec
Auto Auto
SQUARE SQUARE
8/74
USER MANUAL
Specified by the user
Specified by the user
Specified by the user
Specified by the user
Specified by the user
Specified by the user
Specified by the user
BT-METEOR