Channeling System; Stove 14,5 Kw (Mod. Lola, Sara, Eva And Coral); Servicing And Care; Burner Cleaning - Bio Bronpi Aire Serie Instrucciones De Instalación, Uso Y Mantenimiento

7

CHANNELING SYSTEM

Below is detailed the operation of the air distribution system to other adjacent or upper rooms of the stoves
including this system.
7.1

STOVE 14,5 KW (MOD. LOLA, SARA, EVA AND CORAL)

The models Lola, Sara, Eva and Coral includes on the rear top side two outputs with a 80 mm diameter
corresponding with the forced air output channelling system to heat other adjacent or upper rooms. The
regulation of the channelling system is made by the electronic system of the stove, therefore you can
choose the operation of each one of the pipes and the power level desired to each fan independently. To do
this you have to gain access to menu 1 and choose the fan activation and the working power (see drawing D11).
NOTE: Please note that if you've purchased an Eva-Nc model, this model is not ductable, then this menu is visible but is not operational.
8

SERVICING AND CARE

The maintenance operations guarantee a proper working of the product over
its lifetime. Not making these maintenance operations will affect the security
of the product.
8.1

BURNER CLEANING

The burner cleaning must be made daily (see drawing D12).
• Remove the burner from its place and clean the holes.
• Use a vacuum to get rid of the ashes in the burner. You can buy
a Bronpi vacuum-cleaner in the same Bronpi distributor where you
bought your stove.
8.2

USE OF THE SCRAPERS (IN THE MODELS THAT INCORPORATE IT)

The smoke chamber cleaning allows guarantee the thermal power is constant during a long time. This operation must be made at least once
a day. To do it just use the scrapers placed on the top of the stove, moving up to down and vice versa several
times. (see drawing D13).
NOTE: The models Alba, Kira, Nina, Lola, Eva, Eva-Nc and Coral have not these scrapers.
8.3

CLEANING THE ASH PAN

The ash pan should be emptied when necessary. The stove should not be operated without having the ash
pan inside (see drawing D14).
D14
8.4

SEALS OF THE COMBUSTION CHAMBER AND GLASS FIBRE

The seals guarantee stove hermetic nature and, thus, a proper performance (see drawing D15).
It is necessary to check them regularly; if they are worn-out or damaged they should be replaced immediately.
You can find ceramic cord and self-adhesive fibre at the same Bronpi distributor where you bought your stove.
These operations should be done exclusively by an authorised technician.
An authorised technician must do the maintenance at least once a year.
9.5

CLEANING THE CHIMNEY

When the pellet is burnt slowly, it produces tar deposits and other organic vapours that combined with the humidity to create soot (creosote).
An excessive accumulation of soot may cause problems in the smoke outlet and the flue may catch fire if not maintained.
The cleaning of the stove chimney should only be made when the equipment is cold. A chimney sweep should perform this task and, at the
same time, examine the smoke duct (it is recommended to write down the dates of every cleaning and keep a register of them).
9.6

CLEANING THE GLASS

IMPORTANT:

Clean the glass only when it is cold in order to avoid possible explosion. You can use specific products. You can find
Bronpi vitro ceramic-cleaning product at the same Bronpi distributor where you bought your stove (see drawing D16).
BREAKAGE OF GLASSES. The glasses, as they are vitro ceramic, resist until 750ºC and they are not subject to thermal
shocks. The breakage can only be caused by mechanical shocks (crashes or violent closing of the door, etc). Therefore,
its replacement is not included in the warranty.
INSTALLATION, OPERATING AND SERVICING INSTRUCTIONS 27
D11
Menu 01
1
FAN-2
FAN-3
A
D12
D13
D15
D16
AIR SERIES