Remote Control - Revell Control FORMULA Q Manual Del Usuario

• Never disassemble or alter the battery
contacts. Do not damage or puncture
the battery cells. There is a risk of
explosion!
• The LiPo battery must be kept out of
reach of children.
• When disposing of batteries, they
must be discharged or their capacity
must be fully depleted. Cover exposed
terminals with adhesive tape in order
to prevent short-circuiting!
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the remote control and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
Technical changes and differences in
color reserved!
1A Status LED
1B Rotors
1C Protective guard
1D Battery compartment cover

2 rEmotE control

2A Control for thrust and rotation
2B Control for forward/backward
and sideways
2C Trim for rotation
2D Trim for forwards/backwards
2E Trim for sideways
2F ON/OFF switch
2G No function
16
Required batteries for the model:
Power supply:
Rated output:
1 x DC 7,4 V / 8,9 Wh
rechargeable
LiPo battery (included)
Capacity: 1200 mAh
Battery requirement for the
remote control:
Power supply:
DC 9 V
Batteries:
6 x 1.5 V "AA"
(not included)
Charger:
Power supply:
110-240 V AC; 50-60 Hz;
Rated output:
7,4 V DC; 800 mA
1 modEl
1E Battery compartment securing screw
1F ON/OFF switch
1G No function
2H Headless mode
2I Power LED
2J Antenna
2K Turbo switch
2L Flip button
2M Battery compartment cover
2N Battery compartment securing screw
2O Battery compartment opening tab
3 insErting battEriEs (rEmotE control)
3ATo open the battery 3B Insert 6 x 1.5 V AA batteries
compartment, unscrew and pay attention to the
the locking screw (2N) polarity specifications, as
counter-clockwise and indicated in the battery
compartment.
open the battery
compartment cover (2M)
to the top by pressing
down the opening lever
(2O).
4 charging thE modEl
Attention: The battery and motor must cool down for 15 to 30 minutes before charging
and after every flight. Otherwise they can be damaged. The charging process must
be constantly monitored. Always ensure that the charging process takes place on a
fireproof surface in a fire-resistant environment.
• Open the battery compartment cover (1D) by unscrewing the battery compartment
securing screw (1E) in anti-clockwise motion (4A). Unplug the battery from the model
(4B) and switch off the remote control (4C). Remove the battery from the model. Plug
the charger into an unoccupied socket (4D). The status LED on the charger begins to
illuminate.
• Plug the white balancer plug into the charging socket of the charger and ensure the
correct polarity (4E). The battery must be gently inserted into the charging socket –
DO NOT USE FORCE. If the battery is not correctly inserted into the charging socket,
the battery may become damaged and, under certain circumstances, cause injury.
• The status LED on the charger will light up red when charging begins.
• The charging process lasts approx. 140 minutes and must be continuously monitored.
The colour of the LED on the charger changes from red to green when the charging
process is finished.
• Disconnect the battery from the charger and disconnect the charger from the outlet
after the charging is completed.
The model can fly for approx. 8-10 minutes after a charge time of approx.
140 minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
5 start prEparation
The model must be switched on first in order to connect it to the remote control. Open
the battery cover (1D), insert the battery into the battery compartment of the model, plug
the battery plug into the socket in the model, and close the battery compartment. Do not
use force and ensure the correct polarity (5A). Then set the ON/OFF switch on the
model (1F) to the „ON" position.
Before switching on the remote control, the control for thrust and rotation (2A) must
point down (5B). To switch on the remote control, move the ON/OFF switch (2F) to
the ON position and briefly push the control for thrust and rotation upwards. After
approx. 3 seconds, the model activates and is ready for use.
Once you have finished flying, switch the model off first and then the remote control.
Unplug the battery from the model and remove the battery from the model.
3C Close the battery
compartment cover
and screw in the
locking screw (2N)
clockwise.
17