Spa Maintenance - Jacuzzi J-300 Serie Manual De Instalacion Y Uso & Mantenimiento

To activate and deactivate the lock modes, follow the steps below:
A. Press the Menu (
Menu. The LED screen will display "LOC."
B. Press the Warmer (
screen will display the current status of the Lock Mode setting,
either L1, L2, L3 or OFF.
C. Press the Warmer (
D. Once the new setting appears of the display, press the Jets Jets
1 ( ) button to confirm your selection. The display of the LED
screen will blink twice to indicate that the change has been accept-
ed. You must press the Jets 1 (
tion or the current settings will remain active.
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current set-
tings will remain active.
I
Top Menu Lock
To prevent unauthorized use of the menu features, you can lock
the Menu access button. When the lock feature is activated, ac-
cess to the Primary Filtration, Secondary Filtration, CLEARRAY, E-
conomy and Lock programming menus is deactivated. The tem-
perature setting feature, jets pumps operation and lighting fea-
tures are still accessible.
I
Programming the Top Menu Lock Feature
To activate the Top Menu locking feature, follow the steps below:
A. Press and hold the Menu (
B. The LED screen will display "LOC." The LOC display will also
blink twice to indicate that the change has been accepted.
C. When done the LED display will return to the temperature
display.
D. When the LOC feature is active, any time you press the Menu
( ) button, the LED will display "LOC."
To deactivate the Top Menu locking feature, follow the steps below:
A. Press and hold the Menu (
B. The LED screen will display "LOC." The LOC display will also
blink twice to indicate that the change has been accepted.
C. You will now have access to the Menus.

Spa maintenance

Proper and regular maintenance of your spa will help it retain its
beauty and performance.
Information regarding spa cleaning and maintenance and
the products to be used can be found in the catalogue-guide
provided with the product.
I
Cleaning the filters
Your Jacuzzi ® Premium spa is equipped with a skimmer bag and
two high-performance pleated filter cartridges located under
the filter cover.
The circulation pump drawing water through the skimmer bag
and filter cartridge filters fine debris. Large debris is filtered by
jets pump 1 drawing water through the skimmer bag and second
filter cartridge during an automated skimming/heating cycle or
when jets pump 1 is manually acrivated during spa use. Com-
bined, both filters provide unsurpassed water quality by trap-
) button five times to display the Lock
) button to enter the menu. The LED
) button to scroll through the modes.
) button to confirm your selec-
) button for 10 seconds.
) button for 10 seconds.
ping surface oils and suspendend particles. The filter cartridge
should be cleaned once a month or as necessary, depending on
use, for optimum performance.
Dispenser for water sanitation
At authorized Jacuzzi dealers, you can purchase a dispenser where
you can place products for water sanitation).
This dispenser must be placed in the filtering cartridge (recognizable
by the grille cover on the compartment) connected to the circulation
pump.
The dispenser must always be removed (while wearing latex gloves)
along with its cover during cleaning of the filter, and is to be rein-
stalled when this operation is complete.
ALWAYS TURN POWER TO SPA BEFORE CLEANING THE FILTER
CARTRIDGES!
Refer to the filter cleaning/replacement procedure below:
B
A. Turn off power to spa.
B. Lift upward on filter cover to remove it from the mating re-
taining clips, then tilt forward to access filter cartridges.
C. Remove skimmer bag from clips, clean out, then clean out debris.
D. Rotate each filter cartridge handle counter clockwise to un-
thread from mating wall fitting.
E
30
C
(Filter Cover Back View)
F
D
G
Trapped
Air
Bubbles