Technical Specifications; Maintenance Chart - Solo Port 423 Instrucciones

Technical Specifications
Engine type
Displacement
Bore/Stroke
Power
Carburetor
Ignition
Fuel Tank Capacity
Total Formula Tank Capacity
Nominal Formula Tank Capacity
Max. Blower Air Volume
Dimensions without Spray Tube
Weight net
Sound Pressure Level L
WA av
Work Site related noise emission L
Medium value of oscillation acceleration on handle
to EN 28662-1*
* Data provided include measurements at idling and full speed at equal parts.

Maintenance Chart

Carburetor
Air Filter
Spark Plug
Cooling air inlet
Cylinder Fins
Fuel Tank
All accessible screws
(except for carburetor
adj. Screws)
Operating handle
Overall Unit
Workshop service, replacement parts and guarantee
Maintenance and repair: Maintenance and repair of modern motorized devices, as well as their safety-relevant assemblies, require qualified, specialized
training and a workshop equipped with special tools and test devices. Thus SOLO recommends that you have a specialized SOLO workshop carry out all
work that is not described in these operating instructions. Your SOLO specialist has the required training, experience, and equipment at his disposal to
provide you with the most cost-effective solution and can help you in many ways with advice and service. Replacement parts: Dependable operation and
the safety of your device also depend on the quality of the replacement parts that you use. Use only original SOLO replacement parts. Only original parts
come from the production of the device and thus guarantee the highest possible material quality, dimensional accuracy, function, and safety. Original
replacement parts and accessory parts are available from your dealer. He also maintains the requisite replacement part lists to determine the required
replacement part numbers, and he is constantly provided with information concerning detail improvements and innovations in the replacement part
offering. Please note as well that guarantee performances from SOLO are not possible if parts other than SOLO original parts are used. Guarantee: SOLO
guarantees problem-free quality and will assume the costs for defect remediation by replacing the defective parts in the case of material or manufacturing
defects that occur within the guarantee period after the date of purchase. Please note that specific guarantee conditions apply in some countries. Ask your
sales person if you have any questions. As vendor of the products he is responsible for the guarantee.
We request your understanding that no guarantee can be assumed for damages due to the following: • Non-compliance with the operating instructions.
• Neglecting required maintenance and repair work. • Damages due to improper carburetor adjustment. • Normal wear and tear. • Obvious overload
through persistently exceeding the upper performance limits. • Using non-approved tools and cutting fixtures. • Using non-approved cutting bar and chain
lengths in the case of chain saws. • The use of force, improper handling, misuse, or accident. • Damages caused by overheating due to dirt build up on the
ventilator casing. • Intervention by non-specialized persons, or improper repair attempts. • The use of unsuitable replacement parts or parts other than
SOLO original parts to the extent that they cause damage. • Using unsuitable fuel or fuel that has been stored too long. • Damages that can be traced to
implementation conditions from the rental business. Cleaning, care, and adjustment work are not recognized as guarantee performances. All guarantee
work must be carried out by a SOLO dealer.
to EN 11200*
to EN 3774*
PA av
check idling
clean
replace
adjust electrode gap
replace
clean
clean
clean
retighten
functional check
visual check
clean
SOLO single cylinder, two-cycle
ccm
mm
3,0 kW/ 4,1 HP ( 5700 1/min )
kW/hp
electronically controlled magneto ignition,maintenance-free
l
l
l
m 3 /s
hight: 68 / width: 45 / depth: 34
cm
kg
dB(A)
dB(A)
m/s 2
X
X
X
X
17
72,3
48 / 40
Float Type
1,4
12,0
10,0
1400
11,5
96,86
109,56
<6,3
X
X
X
X
X
X
X 1) X
X
(1)
= one time