Briteq LDP-ACCUSPOT 7TC Manual De Instrucciones página 11

ENGLISH
"ChMd" Channel Mode
The unit has 5 different channel modes, refer to the DMX-chart to see the differences.
 Press the MENU button until "ChMd" is shown on the display.
 Press the ENTER button to select.
 Use DOWN and UP button to select one of the available channel modes.
 Once the mode is selected, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds to return to running mode.
"SLMd"Slave Mode
By choosing the right slave mode you can improve the impact of the multi-channel shows while the
units are used in Master/slave mode.
The first projector in the chain should be set to "MaSt", first slave should be in "SL 2" mode, the second in
"SL 3" mode, etc. until "SL16".
 Press the MENU button until "SLMd" is shown on the display.
 Press the ENTER button to select.
 Use DOWN and UP button to select one of the available slave modes.
 Once the right mode is selected, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds to return to running mode.
"baLa" Adjust White balance
Makes it possible to adjust the white color when all colors are at maximum.
 Press the MENU button until "baLa" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use the DOWN and UP button to select the "red " or "Gree" or "blue" color.
 Press the ENTER button, the display starts blinking.
 Use the DOWN and UP button to adjust the value from 125 to 255 and press ENTER to confirm.
 Once the mode has been selected, press the ENTER button to confirm.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
"Udrt" Wireless DMX-synchronization
Used to synchronize the optional W-DMX module to the W-DMX transmitter.
 Press the MENU button until "Udrt" is shown on the display.
 Press the ENTER button, the "Udrt" display starts blinking.
 Press the ENTER button again: the "Udrt" display stops blinking while the DMX-led blinks fast.
 IMPORTANT! Make sure to push the SETUP-button on the W-DMX transmitter (Status LED on the
transmitter starts blinking fast) before the DMX-led on LDP-ACCUSPOT stops blinking fast!.
 Wait until both LEDs stop blinking fast: the synchronization is done
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Note: to break the link (synchronization) between the W-DMX transmitter and the LDP-ACCUSPOT: simply
repeat the same actions but DO NOT press the SETUP-button on the transmitter.
"batt" Battery status
Used to check the precise status of the battery.
 Press the MENU button until the display shows "batt".
 Press ENTER button, the display will show the current status of the battery, shown in %: 5 to 100%
100% means that the battery is full, once the display shows 5% the output stops and charging is needed.
 To go back to the functions press the MENU button again.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
"bLMd" Blackout Mode
With this option you determine how the projector should react while no DMX-signal is detected.
ALWAYS set to "No Blackout" when the unit is used in standalone or master (master/slave) mode!!!
 Press the MENU button until "bLMd" is shown on the display.
 Press the ENTER button.
 Use DOWN and UP button to select one of the 3 options:
 "no": when no DMX-signal is detected, the unit automatically switches to master mode.
 "YeS": when no DMX-signal is detected, the unit shuts down the output (blackout)
 "hold": when no DMX-signal is detected, the unit keeps the last received data on the output.
BRITEQ
®
9/69
USER MANUAL
LDP-ACCUSPOT 7TC