Do not hand wash the filter foam, do
not wring it, do not wash it in washing
machines. Avoid crumpling, stretching
and deforming. After cleaning dry the foam in
room temperature. Never dry the foam on
heaters, stoves, etc.
INLET FILTER
1
Press the "PRESS" button and remove the tank lid.
2
Remove the SAFBAG (21) dust bag module from
the container.
3
Take out the SAFBAG dust bag from the module
(see chapter TRADITIONAL CLEANING WITH SAFBAG
DUST BAG – disassembly/assembly of the SAFBAG
dust bag).
4
Release the fastening hook which fixes the lid of
the SAFBAG dust bag module with the basket and pull
the basket aside.
5
Take out the filter, wash it under running water, dry
and reinsert.
6
Close the basket of the SAFBAG dust bag module
by pressing it until you hear a characteristic click.
7
Insert SAFBAG dust bag (see chapter
TRADITIONAL CLEANING WITH SAFBAG DUST BAG
– disassembly/assembly of the SAFBAG dust bag).
8
Insert the dry filtration module with the SAFBAG (21)
dust bag into the tank.
● Insert and snap the tank lid shut.
MOTOR FILTER
A filtration fabric is inserted in the motor cooling
cycle which is to catch the coal dust which arises due
to the natural wear and tear of the brushes and the
commutator in the motor.
1
Remove the tank from the vacuum cleaner.
2
Place the vacuum cleaner with the "wheels upwards"
so that the upper sloping surface and the handle are rested
on the floor. Insert a flat, narrow tool e.g. a screwdriver into
the special slot of the filter lid; pry the fastening with an
upward hand movement (lever principle) which will release
the lid wwlatch while being bent.
3
If the motor filter (7) is dirty, it is possible to rinse
the filter (7) under running water. Remember to dry the
above mentioned filter before reassembly.
4
Insert the new/rinsed motor filter (7), make sure
that the filter edges do not remain outside the outline
of the section. Snap the filter lid shut by first inserting
the lower fastening and then pressing the fastening so
that the upper fastening clicks into place at the edge of
the appliance body.
OUTLET EPA FILTER AND FOAM FILTER III
The EPA outlet filter should be replaced after about
30 hours of operation (6 months) or earlier in case of
heavy dirt.
1
Remove the tank from the vacuum cleaner.
2
Place the vacuum cleaner with the "wheels upwards"
so that the upper sloping surface and the handle are
H
rested on the floor.
3
Slide the slider of the filter cover interlock to the
"open" position and remove the filter lid.
4
Remove the foam filter III (10). Rinse or replace
if the filter becomes dirty. Remember to dry the filter
before reassembly.
5
Remove the foam filter III (10) and next remove the
EPA filter by grabbing the handle. Replace with a new
one if the filter becomes dirty.
It is recommended to periodically inspect the condition
of the filter, especially if there was a water overflow to the
outside of the vacuum cleaner. In case of detecting damage
(a break) in the filter layer or if the layer is evenly covered
with dust, the filter should be replace with a new one.
6
If the EPA filter is dirty, replace it with a new one or
rinse under running water. Remember to dry the filter
before reassembly.
7
Reinsert the filters, insert the filter lid and press firmly.
8
Slide the slider of the filter cover interlock to the
"closed" position.
Turn the vacuum cleaner to its natural position (on four
wheels).
Disposal
I
Dispose of packaging in an environmentally-friendly
manner. Our goods come in optimised packaging.
This basically consists in using non-contaminating
materials which should be handed over to the local
waste disposal service as secondary raw materials.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances
(waste electrical and electronic equipment
– WEEE). The guideline determines the framework for
the return and recycling of used appliances as applicable
throughout the EU. Please ask your specialist retailer
about current disposal facilities.
The manufacturer does not accept any liability for any damages
resulting from unintended use or inappropriate handling.
The manufacturer reserves his rights for modifying the product
any time in order to adjust it to law regulations, norms, directives,
or due to construction, trade aesthetic or other reasons, without
notifying it in advance.
J