Details For Ordering - Alarmcom IS443 Manual De Instalación

Troubleshooting
Operation LED does not light
1. Disruption of power or inadequate power.
– Correct power supply.
2. Bad wiring connections or broken wire, short.
– Check and correct wiring.
Receiver Alarm LED does not light when the beam is
broken.
1. Disruption of power or inadequate power.
– Correct power supply.
2. Bad wiring connections or broken wire, short.
– Check and correct wiring.
3. Beam reflection is flooding receiver.
– Remove the reflecting object. Contact Alarmcom for
further remedies.
4. Four beams are not broken simultaneously.
– Ensure all beams are broken at same time.
5. Beam interruption time is shorter than response time.
– Adjust response time.
Receiver Alarm LED stays lit
1. Alignment is out.
– Check and adjust.
2. Obstruction between Transmitter and Receiver.
– Check site / remove any possible obstacles.
3. Optics of units are dirty.
– Clean the optics with a soft cloth.
4. Frequency channel setting on transmitter does not
match with that on receiver.
– Readjust to the same channel.
Intermittent alarm
1. Bad wiring connection.
– Check again.
2. Change of supply voltage.
– Stabilize supply voltage.
3. Obstructing object between Transmitter and Receiver.
– Remove the obstruction.
4. Transient spikes on supply cables.
– Re–locate.
5. Loose installation of Transmitter and Receiver.
– Tight on.
6. Optics of units are dirty.
– Clean the optics with a soft cloth.
7. Poor alignment.
– Check and adjust again.
8. Animals pass through the four beams.
– Change environment or the installation.
9. Beam power switch is set at L, which is not sensitivity
enough.
– Set beam power switch to H and make the unit gain–
locked with the receiver cover detached.
Approvals
CE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
National approval conditions relating to the use of the
product must be followed.
6
Specifications
Detection system
. . . . . . . . . . . . . . . . .
Infrared beam
. . . . . . . . . . . . . .
Protection distance
– IS443 outdoor
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– IS444 outdoor
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– IS445 outdoor
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Max. beam range
– IS443
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– IS444
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– IS445
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Responce time
. . . . . . . . . . . . . . . . . .
Supply voltage
. . . . . . . . . . .
Current consumption
– IS443
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– IS444
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– IS445
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarm output
. . . . . . . . . . . . . . . . . .
Environmental ouput
. . . . .
Tamper output
. . . . . . . . . . . . . . . . . . . . . . .
Alarm LED
. . . . . . . . . . . . . . . . .
Attenuation LED Red LED (Receiver) lights when
. . . . .
Functions Modulated beam frequency selection
. . . . . . .
Ambient temperature
. . . . . . . . . . . . . . .
range
Mounting position
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Weight
– Transmitter
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– Receiver
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appearance
. . . . . . . . . . . . . . . . . . . . . . .

Details for ordering

IS443 Photoelectric beam sensor (50m)
IS444 Photoelectric beam sensor (100m)
IS445 Photoelectric beam sensor (200m)
BP–200F Pole cover (2pcs./set)
conform
HTF–24 Heater (2pcs./set) 24VDC; 860mA
Limited warranty
Alarmcom products are warranted to be free from defects
in material and workmanship for 12 month from original
date of shipment. Our warranty does not cover damage
or failure caused by Acts of God, abuse, misuse, abnor-
mal usage, faulty installation, improper maintenance or
any repairs other than those provided by Alarmcom. All
implied warranties with respect to Alarmcom, including
implied warranties for merchantability and implied war-
ranties for fitness, are limited in duration to 12 months
from original date of shipment. During the Warranty Peri-
od, Alarmcom will repair or replace, at its sole option, free
of charge, any defective parts returned prepaid. Please
provide the model number of the products, original date
of shipment and nature of difficulty being experienced.
There will be changes rendered for product repairs made
after our Warranty Period has expired.
Near infrared beam
interruption system
Double modulation pulsed
beam by LED
50m
100m
200m
200m
400m
600m
50msec. to 700msec.
12V to 30VDC (non–polarity)
95mA
105mA
120mA
Dry contact relay output
Reset: Interruption time +
off–delay (approx. 1.5sec.)
Contact: 30V (AC/DC), 1A
Dry contact relay: switchover
Contact operation: Output when
weather condition gets worse
Contact: 30V (AC/DC), 1A
Dry contact relay
Contact operation: Output when
receiver cover is detached
Contact: 30V (AC/DC), 0,1A
Red LED (Receiver) lights
when an alarm is initiated
beam receiption is attenuated
Tone indicator
Environmental module
Alarm memory indication
Programmed AGC
Auto–Gain Lock function
Monitor Jack
-25°C to +66°C
Outdoor
Terminals
1.200kg
1.300kg
PC resin (wine red)
529 992
. . . . . .
529 989
. . . . .
529 950
. . . . .
538 624
. . . . . . . . . . . . . .
538 611
. . .