Publicidad
Idiomas disponibles
Idiomas disponibles
~
Alternating Current
n o
No Load Speed
Eye protection should be worn at
(9.13)
all times when using this tool.
iNTENDED uSE
Hard Hat—Head protection
• This power tool is intended to be used for
should be worn at all times
drilling holes with annular cutters and twist
whilst using this tool, to protect
drills in an industrial environment.
from overhead hazards
• The machine is designed to be held
onto a ferrous surface using its
Ear protection / Ear defenders
electromagnetic base.
should be worn at all times whilst
• This power tool should be used in a
using this tool, this tool exceeds
weather protected environment, and be
85dB(A)
used with the accessories provided, or
Evolution Power Tools recommended
accessories only.
Wear Dust Protection
• The power tool can be used vertically,
horizontally and and in an inverted
position, provided the magnetic adhesion
and work environment allow.
Electrical enclosure -
risk of electric shock.
waRNiNg: To prevent ingress of fluids
into the electrical system, cutting paste
read and understand
should be used rather than cutting fluid
the instruction manual -
when using the machine in the inverted
before operating this tool.
position.
£
Caution ! / Attention !
(9.14)
PRohiBiTED uSES
• This power tool should never be used without
Fuse
a ground or protective earth connection.
• This power tool should not be used in a
Ce certification
potentially explosive environment.
• This power tool should not be used in a wet
or humid environment where water could
be drawn into the power tools cooling and
ETL certification
ventilation system.
• if the power tool is used in the inverted or
horizontal position, cutting fluids should
not be used to prevent ingress of fluids into
Triman - waste Collection
the electrical system. Cutting paste should
& recycling
be used instead.
6
www.evolutionpowertools.com
WEEE - Waste Electrical
and Electronic Equipment This
machine should be disposed of
as Electrical & Electronic Waste.
www.evolutionpowertools.com
• This power tool should never be positioned
on a work piece between the electrode and
ground of an arc type welder. Damage to
the machine will result as the welder will
ground through the power tools ground or
earth cable.
• This power tool should not be used
where the voltage is abnormally lower
than the rated voltage, subject to voltage
tolerances. Check the power tool rating
plate, check the voltage available.
waRNiNg: Operating on a lower than rated
voltage will result in the electro magnet
being at reduced power and the machine may
become insecure whilst cutting.
(1.13)
waRNiNg: This machine is not intended
for use by persons (including children) with
reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning the safe use of the machine by a
person responsible for their safety and who is
competent in its safe use.
Children should be supervised to ensure
that they do not have access to, and are not
allowed to play with, this machine.
(1.14)
ElEcTRical SaFETy
This machine is fitted with the correct
moulded plug and mains lead for the
designated market. If the supply cord is
damaged, it must be replaced by a specific
cord or assembly available from the
manufacturers or its service agent.
(1.15)
ouTDooR uSE
waRNiNg: For your protection, if this tool is
to be used outdoors it should not be exposed
to rain, or used in damp locations. Do not place
the tool on damp surfaces. Use a clean, dry
workbench if available. For added protection
use a residual current device (r.C.D.) that will
7
interrupt the supply if the leakage current to
earth exceeds 30mA for 30ms. Always check
the operation of the residual current device
(r.C.D.) before using the machine.
If an extension cable is required it must be a
suitable type for use outdoors and so labelled.
The manufacturer's instructions should be
followed when using an extension cable.
(2.1)
PowER Tool gENERal
SaFETy iNSTRucTioNS
(These General Power Tool Safety Instructions
are as specified in BS EN 60745-1:2009 & EN
61029-1:2009)
waRNiNg: Read all safety warnings and
instructions. Failure to follow the warnings
and instructions may result in electric shock,
fire and/ or serious injury.
Save all warnings and instructions for
future reference.
The term "power tool" in the warnings refers
to your mains-operated (corded) power tool
or battery-operated (cordless) power tool.
(2.2)
1) general Power Tool Safety warnings
[work area safety]
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in
explosive atmospheres, such as in the
presence of flammable liquids, gasses or
dust. Power tools create sparks which may
ignite the dust or fumes.
c) Keep children and bystanders away
while operating power tool.
Distractions can cause you to lose control.
(2.3)
2) general Power Tool Safety warnings
[Electrical Safety]
a) Power tool plugs must match the
outlet. Never modify the plug in any way.
Do not use any adapter plugs with
EN
ES
FR
TR
Publicidad
