Inserting Batteries Into The Ifill Oxygen Cylinder W/Pulsedose; Using Your Oxygen Ifill Cylinder W/Pulsedose; Using Your Ifill Continuous Flow Oxygen Cylinder - DeVilbiss Healthcare iFill PD1000A Serie Guía De Instrucciones

Inserting Batteries Into The iFill Oxygen Cylinder w/PulseDose

1 2
note– When changing Open the battery door. Insert 2
"AA" Alkaline or NiMH
batteries, first turn the rotary
batteries (observe polarity).
selector to the "OFF" position.
Using Your iFill Oxygen Cylinder w/PulseDose
1 2
Attach the standard nasal Attach the cannula to your
cannula to the cannula fitting. nose and face.
Oxygen tubing up to 35 feet
long may be used in
PulseDose delivery mode.
waRNING
To prevent injury from cylinders tipping over, do not use cannula tubing lengths over 10 feet with small compressed oxygen cylinders. Unattended cylinders should be secured in a
cylinder stand.
noteS
• When this rotary selector is set to "OFF," the unit is not using battery power and will not pulse. When the selector is set to one of the numbers, the unit is on and awaiting inspiration through
the nasal cannula at which time it will dose on every breath. The volume of the oxygen delivered varies according to which prescription flow setting is chosen. The final setting on the rotary
switch is "CF"; this is the continuous flow position. In this position oxygen will flow from the cannula fitting at the default continuous flow rate.
• Continuous flow mode is not powered by the batteries and can be used regardless of the battery level. In the event of a device failure or dead batteries, the user must manually switch the unit
to continuous flow for delivery of oxygen. The device will not automatically switch to continuous flow. The oxygen cylinder will not last as long in continuous flow mode as it would in
PulseDose mode. Unless there is a problem with the unit, such as dead batteries, the unit should be used in PulseDose mode.
• When operated within the specified Operating Temperature Range, there is no "warm up" period required. Should the device be outside the specified Operating Temperature Range, allow the
unit to stabilize within the Operating Temperature Range prior to use.
• A mask should not be used in the PulseDose delivery mode as it may not fit to the face well enough to allow the conserving device to sense inhalation efforts. Also, the therapeutic effect of
PulseDose would not be realized, as the dose of oxygen would be diluted in the mask prior to inhalation.
• A pediatric or low-flow cannula should not be used in PulseDose delivery mode. The reduced diameter of the cannula causes too much back pressure and will affect the oxygen volume
delivered.
• PulseDose delivers oxygen in a very short "puff." It does not deliver oxygen during the entire inhalation. The length of time that PulseDose delivers oxygen will not vary from breath to breath.
The time is set in correlation to the oxygen dosage set on the conserving device (patient's prescription setting).
• PulseDose is designed to prevent the delivery of pulses more than every 1 1/2 seconds. If the breath rate is greater than 40 BPM, this feature prevents delivery of excessive oxygen by not
dosing on every breath.
• If using NiMH batteries, carefully monitor when the low battery indicator flashes red. It is recommended that a spare fully-charged set of alkaline batteries be kept in reserve and installed
when the change battery indicator is constant red.
• Always follow the Use and Care instructions supplied with the batteries being used. Batteries should be removed when the device will not be used for a week or more.
• The iFill Oxygen Cylinder w/PulseDose and w/Continuous Flow Regulator are Latex free. Review the individual material lists for the tubing and cannula used in conjunction with the DeVilbiss
products.
alerts (PD1000a-CaN-M4, -M6, -ML6, -C, -D, and -E)
no inspiration Alert – If the unit is on and inspiration has not been sensed for 15 seconds, the audible alert will activate until either an inhalation is sensed or the rotary selector is changed to the
"OFF" position.

Using Your iFill Continuous Flow Oxygen Cylinder

1 2
Attach the nasal cannula (or Attach the cannula/mask to
mask) to the cannula fitting. your nose and face.
EN - 6
3
Close the battery door.
3 4
Turn "ON" by turning the rotary Breathe normally, the
selector to the prescribed flow conserving device will deliver
setting. Always confirm that a bolus of oxygen at the
the green and red lights flash leading edge of inspiration on
and on PD1000A-CAN-XX every breath up to 40 breaths
models you hear the audible per minute.
alarm beep at startup.
3 4
Turn the rotary selector to the Breathe normally.
prescribed flow setting. When
the selector is set to one of the
numbers, the unit is on.
DAnGeR–no SMoKinG
5
When you are finished using
the iFill oxygen cylinder, turn
the rotary selector to the
"OFF" position.
5
When you are finished using
the iFill oxygen cylinder, turn
the rotary selector to the
"OFF" position.
waRNING
To prevent injury from
cylinders tipping over, do
not use cannula tubing
lengths over 10 feet with
small compressed oxygen
cylinders. Unattended
cylinders should be secured
in a cylinder stand.
A-535-CYL