Listening Through A Receiver; Check Points Before Requesting Service - Samsung 4 Serie Manual Del Usaurio

Listening through a Receiver

You can listen to sound through a receiver instead of the TV speaker.
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Input, then press the ENTER button.
Press the ▲ or ▼ button to select Anynet + (HDMI-CEC), then press the ENTER

button.
 Press the ▲ or ▼ button to select Receiver, then press the ENTER button.
4 Press the ◄ or ► button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
5 Press the EXIT button to exit.
➢
When the receiver is set to On, you can listen to the TV sound through the 2-channel
receiver.
➢
If the receiver is exclusively for a home theater only (supporting audio only), it may
not appear in the device list.
➢
Only when you have connected the optical jack of the TV and the receiver properly, does Receiver work.
➢
In case of a content with copyright problems, listening through the receiver may not properly operate.

Check Points before Requesting Service

Symptom
Anynet + does not work.
I want to start Anynet + .
I want to exit Anynet + .
The message Connecting to
Anynet + device... appears
on the screen.
The Anynet + device does
not play.
The connected device is not
displayed.
The TV programme cannot
be recorded.
The TV sound is not output
through the receiver.
Solution
Check if the device is an Anynet + device. The Anynet + system
■
supports Anynet + devices only.
■ Connect only one receiver.
Check if the Anynet + device power cord is properly connected.
■
Check the Anynet + device's Video/Audio/HDMI cable connections.
■
Check whether Anynet + (HDMI-CEC) is set to On in the Anynet +
■
setup menu.
■ Check whether the TV remote control is in TV mode.
Check whether it is Anynet + exclusive remote control.
■
Anynet + doesn't work at a certain condition. (Searching channels)
■
■ When connecting or removing the HDMI cable, please make sure
to search devices again or restart your TV.
Check if the Anynet + Function of Anynet + device is set on.
■
Check if the Anynet + device is properly connected to the TV and
■
check if the Anynet + (HDMI-CEC) is set to On in the Anynet +
Setup menu.
■ Press the TV button on the TV remote control to switch to TV.
Then press the TOOLS button to show the Anynet + menu and
select a menu you want.
Select View TV in Anynet + menu.
■
■ Press the SOURCE button on the TV remote control and select a
device other than Anynet + devices.
■ Press any of P, CH LIST, and PRE-CH to change to the
TV mode. (Note that the channel button operates only when a
tuner-embedded Anynet + device is not connected.)
■ You cannot use the remote control when you are configuring
Anynet + or switching to a view mode.
Use the remote control when the Anynet + setting or switching to
■
view mode is complete.
■ You cannot use the play function when Plug & Play is in progress.
Check whether or not the device supports Anynet + functions.
■
■ Check whether or not the HDMI cable is properly connected.
Check whether Anynet + (HDMI-CEC) is set to On in the Anynet +
■
setup menu.
Search Anynet + devices again.
■
You can connect an Anynet + device using the HDMI cable only.
■
Some HDMI cables may not support Anynet + functions.
■ Check whether the antenna jack on the recording device is
properly connected.
■ Connect the optical cable between TV and the receiver.
English - 45
TV P 1
View TV
Select Device

Record

Menu on Device

Device Operation

Receiver :On

Setup

Move
Enter
Exit