Evolution R255SMS-DB Instrucciones Originales página 29

www.evolutionpowertools.com
LASER ADJUSTMENT
WARNING: At no time during this procedure
should the motor be started.
To check laser alignment:
• Set mitre table to 0˚.
• Place a piece of cardboard, or similar, onto the
rotary table of the machine.
• With the carriage slide in the rearmost position,
lower the cutting head so that a blade tooth
makes a mark in the cardboard.
• Allow the cutting head to rise, and then
repeat the above with the carriage slide in an
approximate mid- way position.
• Again repeat, but with the carriage slide moved
to its most forward position.
• With the cutting head raised, turn on the laser and
slide the cutting head backwards and forwards to
observe if the projected laser beam is in line with
the marks previously made:
• Beam is aligned with the marks = No further
action required.
• Beam is not parallel with the
marks = Follow section A.
• Beam is parallel but not aligned with the marks
= Proceed to section B.
A. If the laser beam is not parallel to the marks
proceed as follows:
• Loosen the clamping screw. (Fig. 45-a)
• Carefully rotate the laser module, until the line
is parallel with the marks in the cardboard.
• Re-tighten the clamping screw.
• Recheck the alignment.
B. If the laser beam is parallel with the marks, but
not going through them:
• Slacken the two screws. (Fig. 45-b)
• The laser mounting block can now be moved
sideways to align the laser beam with the marks
made in the cardboard.
• When the laser beam is in the correct place,
re-tighten the two screws.
• Repeat procedure 'A' to check alignment.
Note: The above adjustments & alignments
should be checked on a regular basis to ensure
laser accuracy.
Note: The following WARNING labels can be
found on this machine:
LASER LIGHT
Warning: Do not stare into the beam
Wavelength: 650nm
Output Max: ≤ 1mW
CLASS 2 LASER PRODUCT
EN 60825-1:2014
LASER RADIATION AVOID DIRECT EYE CONTACT
PERMANENTLY MOUNTING THE
MITRE SAW
To reduce the risk of injury from unexpected saw
movement, place the saw in the desired location
either on a workbench or other suitable machine
stand. The base of the saw has four mounting
holes through which suitable bolts (not supplied)
can be placed to secure the mitre saw. If the saw
is to be used in one location, permanently fasten
it to the workbench using appropriate fastenings
(not supplied). Use locking washers and nuts on
the underside of the workbench. (Fig. 46)
• To avoid injury from flying debris, position the
saw so that other people or bystanders cannot
stand too close (or behind) it.
• Locate the saw on a firm, level surface where
there is plenty of room for handling and
properly supporting the work-piece.
• Support the saw so the machine table is level
and the saw does not rock.
• Bolt or clamp the saw securely to its support
stand or workbench.
Note: This machine can be attached to the
Evolution Mitre Saw Stand. (Fig. 47). This will
provide a safe secure, and extremely portable
workshop stand which is capable of handling
long pieces of material. Operator efficiency and
safety may thus be enhanced, as well as operator
fatigue reduced.
For portable use:
• Mount the saw on a 18mm (11/16 in)
thick piece of plywood or MDF (800mm x
500mm (31-1/2in x 19-11/16in) min size
recommended) using appropriate fastenings
(not supplied).
Note: It may be necessary to countersink the
washers, nuts, etc. to the underside of the
plywood or MDF mounting board. The underside
needs to be smooth and flush with no protruding
fixings etc.
• Use 'G' clamps to attach the mounting board to
the work surface. (Fig. 48)
29
EN