Descargar Imprimir esta página

Soundcast VG5 Manual Del Usuario página 6

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 7
Other Controls and Features
Volume Control:
The VG5 volume can be adjusted when playing music
or during speakerphone operation by pressing or press
and holding the + (up) or – (down) volume adjustment
buttons on the keypad. The current volume level will be
displayed with blue LED's on the volume bar graph.
➤ Mobile devices that support the AVRCP protocol
can adjust the volume from the mobile devices
volume slider control.
Fuel Gauge:
Press the Power button for (1) second and beep is
heard to display the current battery level bar graph us-
ing a combination of RED=Low, YELLOW=OK, GREEN=-
Full LEDs. The bar graph will move counter-clockwise as
the battery discharges.
➤ The fuel-gauge and amber low battery LED indicators
will NOT be accurate until at least two full charging/
discharging cycles have been completed.
Volume Level Indication
Blue LEDs
illuminate in
clockwise direction
to indicate
volume level.
Volume
down
button
Battery Status Indication
Yellow
(Ok
Green
Battery)
(Charged
Battery)
Red
(Low
Battery)
6
Keyboard Lock
The VG5 has two different keypad lockout mechanisms
to prevent un-intended or accidental operation. Both are
disabled by default. When enabled, all keypad functions
except for power on/off will be ignored.
Child Lock:
To Enable or Disable, press and hold the mute button
for (5) seconds and release. The top most BLUE LED
will flash indicating the keypad is locked and child lock
is active. Power cycling the unit will disable the keypad
child lock.
Auto Lock:
Keypad Lock Indicator:
Flashing Blue:
Child Lock Active
Flashing Green:
Auto Lock Active
To Enable or Disable Auto-Lock, press and hold the
mute button for (10) seconds and release. The volume
bar graph will blink twice when enabled and once when
disabled. When enabled, the keypad will "Auto-Lock"
after (3) minutes of no keypad interaction. The top
GREEN LED will blink indicating the keypad is locked The
Volume
Auto-Lock will remain enabled or disabled when power
up
button
cycling the unit.
Temporarily unlock the keypad for use while Auto-Lock is
activeby conducting an "Unlock Swipe". This can be done
by sliding your finger quickly between the power button
and any other function button, being sure to release your
finger while it is still over the "other function" button.
The volume bar graph will blink indicating that the keypad
is unlocked. Keypad will auto-lock again after (3) minutes
of no interaction.
Orange
Power
LED
Temporary Unlock
Swipe Action
Slide finger from power
any
button to
function
button, and release.
Troubleshooting
Problem
• Be sure unit is fully charged
VG5 does not
• Be sure keypad is clear of any dirt,
turn on
Mute
button
• Disconnect / Re-connect battery
• Power cycle VG5 unit(s) and retry
Difficulty with
• Clear both Bluetooth and TWS pairing
Bluetooth or
TWS pairing
process
10 seconds (third beep) and try your
• Disable/Enable Bluetooth function
Keypad has
• Wipe down keypad to remove any
un-intended
operation due
• Utilize Child Lock or Auto Lock features
to moisture
Keypad
• The VG5 utilizes an ambient light
backlights
are changing
brightness or
turn off
Keypad is not
responding
to button
presses
* Perform factory reset by
Unit is
misbehaving or
* Clear both Bluetooth and TWS
not responsive
* Power cycle unit
Solution
dust or moisture
history by holding the Bluetooth button
for 10 seconds (third beep), repeat
by pressing the TWS buttons for a full
pairing again
on your music source device (phone or
computer) and retry
excess moisture or dirt
described above
sensor to adjust the LED backlights
and status LED indicators based on the
ambient light. This is normal operation
Power cycle the unit and be certain
that Child Lock and Auto-Lock functions
are Disabled
Disconnecting & Reconnecting battery
memory (refer to instructions above)

Publicidad

loading

Productos relacionados para Soundcast VG5