Assembly Instructions; Dealer Set Up Instructions - Woods BATWING BW15.50E Manual Del Operador

DEALER SET-UP INSTRUCTIONS
Assembly of this cutter is the responsibility of the WOODS dealer. It should be
delivered to the owner completely assembled, lubricated and adjusted for nor-
mal cutting conditions.
The cutter is shipped partially assembled. Assembly will be easier if compo-
nents are aligned and loosely assembled before tightening hardware. Recom-
mended torque values for hardware are located on page 70.
Select a suitable working area. A smooth hard surface, such as concrete, will
make assembly much quicker. Open parts boxes and lay out parts and hard-
ware to make location easy. Refer to illustrations, accompanying text, parts lists
and exploded view drawings.
Complete the check list on page 27 when assembly is complete and cutter is
delivered to the customer.
WARNING
 Before working underneath, carefully read Operator's Manual
instructions, disconnect driveline, raise mower, securely block up all cor-
ners with jackstands, and check stability. Secure blocking prevents
equipment from dropping due to hydraulic leak down, hydraulic system
failures, or mechanical component failures.
 Do not disconnect hydraulic lines until machine is securely blocked
or placed in lowest position and system pressure is released by operat-
ing valve levers.
CAUTION CAUTION
 Always wear relatively tight and belted clothing to avoid entangle-
ment in moving parts. Wear sturdy, rough-soled work shoes and protec-
tive equipment for eyes, hair, hands, hearing, and head; and respirator or
filter mask where appropriate.
Small Aircraft Tires
Tongue at 279 mm
Tongue at 457 mm
Large Aircraft Tires
Tongue at 279 mm
Tongue at 457 mm
Install Wheel
Figure 21. Centre Section Wheel and Hub Installation
Install Wing Wheel (Figure 22)
1. Insert wheel hub into wing wheel yoke arms (5) and align holes.
2. Secure into position using cap screw (83) and flanged lock nut (88).
3. Attach wheel to hub using five lug nuts. Install the chamfered side of the
lug nut toward the inside for steel rim for pneumatic tires and rims.
Tighten to 115 Nm. Check that tire air pressure is a maximum of .27 MPa.
NOTE: Install the flat side of the nut toward the inside for solid tires
and aircraft tires (shown).
4. Install optional dual wheel and hub to inside of wheel yoke arm.
26 Dealer Service

ASSEMBLY INSTRUCTIONS

Attitude Rod Length Beyond
Nuts (34)
88.9 mm
44.5 mm
114 mm
63.5 mm
1. Centre Wheel Yoke Arm
83. 1/2" NC x 3" HHCS GR5
88. 1/2" NC Flange Lock Nut
5. Wing wheel yoke arm, right
58. Wheel and hub
83. 1/2 NC x 3 HHCS GR5
88. 1/2 NC Flanged lock nut
Figure 22. Wing Wheel - Right
Tandem Axle Arm Installation (Optional for .60 & .70 Series)
Refer to page 68 for Installation and Operation instructions.
Shredding Kit Installation (Optional for .60 & .70 Series)
Refer to page 69 for Installation and Operation instructions.
Double Chain Installation (Optional)
NOTICE
DO NOT REMOVE SINGLE ROW CHAIN AS INSTALLED FROM FACTORY.
DOUBLE ROW CHAIN KIT IS AN ADDITION TO STANDARD SINGLE ROW
CHAIN SHOWN.
1. Remove one single chain locking bracket from unit at a time.
2. Compare removed bracket with new double lock brackets to identify
correct new part. Refer to Figure 23 for example.
Figure 23.
3. Leave single chain in place except where noted.
4. Install chain as shown in pages 62 & 63, doubling over on centre link and
sliding over extended finger. Centre chain loop may be vertical or
horizontal as required for installation.
5. Install new lock bracket and attach with new hardware provided.
6. Repeat for each individual locking bracket.
7. Install rear chain flap on wing tail wheel arms. See page 62.
MAN1246 (04/10/2018)