Nolan N91 EVO Seguridad E Instrucciones página 11

2.3 Insert the left front flap of the liner into its seat on the support fixed to the polystyrene inner shell and push it downwards
until it is completely locked. Follow the same steps for the central and right flap (Fig. 18).
2.4 Insert the right and left side flaps of the liner pushing them into the cavities between the inner polystyrene cheek pads and
the outer shell (Fig. 16).
Note: Check the correct assembly of the liner front area by lifting and lowering the VPS. These movements should be
smooth. If this is not the case, repeat thesteps 1.6 and 2.3.
2.5 Insert the rear right, central and left flaps of the liner into the relevant seats on the support fixed to the polystyrene inner
shell by slightly deforming the shell edge (Fig. 17). Push the flaps until they are fully hooked onto the support.
2.6 Fasten the left snap fastener located on the back of the cheek pad near the roll neck to the outer shell (Fig. 15). Repeat the
same operation on the right side of the helmet.
2.7 Hook the roll neck left eyelet to the left side frame (Fig. 14). Repeat the same operation on the right side of the helmet.
2.8 Push the padding of the cheek pad near the snap fastener located on its back by fastening it to the relevant seat of the
frame fixed to the shell (Fig. 13).
WARNING!!!
- Remove the inner comfort padding only when cleaning or washing is required.
- Never use the helmet before completely and correctly reassembling its inner comfort padding.
- Delicately hand-wash in lukewarm water (max. 30°C) and neutral soap.
- Rinse off with cold water and dry up at room temperature away from direct sunrays.
- Never machine-wash the inner comfort padding.
- The inner polystyrene is an easily deformable material, in fact it is apt to change or get partially destroyed to help absorb
shocks.
- Clean the inner components with a damp cloth only and allow it to dry at room temperature away from direct sunlight.
- Do not modify the helmet's internal polystyrene components in any way.
- Never use tools or equipment of any sort to carry out the steps described above.
2.3 Insert the left front flap of the liner into its seat on the support fixed to the polystyrene inner shell and push it downwards
until it is completely locked. Follow the same steps for the central and right flap (Fig. 18).
2.4 Insert the right and left side flaps of the liner pushing them into the cavities between the inner polystyrene cheek pads and
the outer shell (Fig. 16).
Note: Check the correct assembly of the liner front area by lifting and lowering the VPS. These movements should be
smooth. If this is not the case, repeat thesteps 1.6 and 2.3.
2.5 Insert the rear right, central and left flaps of the liner into the relevant seats on the support fixed to the polystyrene inner
shell by slightly deforming the shell edge (Fig. 17). Push the flaps until they are fully hooked onto the support.
2.6 Fasten the left snap fastener located on the back of the cheek pad near the roll neck to the outer shell (Fig. 15). Repeat the
same operation on the right side of the helmet.
2.7 Hook the roll neck left eyelet to the left side frame (Fig. 14). Repeat the same operation on the right side of the helmet.
2.8 Push the padding of the cheek pad near the snap fastener located on its back by fastening it to the relevant seat of the
frame fixed to the shell (Fig. 13).
WARNING!!!
- Remove the inner comfort padding only when cleaning or washing is required.
- Never use the helmet before completely and correctly reassembling its inner comfort padding.
- Delicately hand-wash in lukewarm water (max. 30°C) and neutral soap.
- Rinse off with cold water and dry up at room temperature away from direct sunrays.
- Never machine-wash the inner comfort padding.
- The inner polystyrene is an easily deformable material, in fact it is apt to change or get partially destroyed to help absorb
shocks.
- Clean the inner components with a damp cloth only and allow it to dry at room temperature away from direct sunlight.
- Do not modify the helmet's internal polystyrene components in any way.
- Never use tools or equipment of any sort to carry out the steps described above.
11
11